Cisco Unified MeetingPlace Release 6.1 -- Cisco Unified MeetingPlace H.323/SIP IP Gateway Software Release 6.0 Installation Worksheets for Use With Release 6.1

From DocWiki

Jump to: navigation, search

Cisco Unified MeetingPlace Release 6.1 > Cisco Unified MeetingPlace H.323/SIP IP Gateway



Complete the following worksheets:


Contents

Installation Worksheet

Before you install Cisco Unified MeetingPlace H.323/SIP IP Gateway, complete the following worksheet.


You need to supply these values when you install and configure Cisco Unified MeetingPlace H.323/SIP IP Gateway.


Description Value Enter Your Value Here

Hostname or IP address of the IP-gateway server.

host name


IP address

____________________________


____________________________

Number of the IP-gateway server.

dialable number

____________________________

Hostname of the Cisco Unified MeetingPlace Audio Server system.

hostname


IP address

____________________________


____________________________

Additional IP addresses of the Cisco Unified MeetingPlace Audio Server system.


Up to four additional IP addresses are needed for the Multi Access blade. If a TP1610 Multi Access blade is in use but only 240 VoIP or fewer are deployed, then you must specify the lower address; the upper address can be set to 0.0.0.0. You must also set the Ethernet switch port or any other network devices to which the Multi Access blade connects directly to fixed 100Base-TX Full Duplex.

Note: Do not set the lower address to 0.0.0.0.

hostname


IP address


hostname


IP address


hostname


IP address


hostname


IP address

____________________________


____________________________


____________________________


____________________________


____________________________


____________________________


____________________________


____________________________

Hostname or IP address of one of the following:

  • Cisco Unified Communications Manager server or IP PBX that runs standard H.323 or SIP call control
  • Cisco SIP Proxy Server

hostname


IP address

____________________________


____________________________

Host name or IP address of the Cisco Unified MeetingPlace Web Conferencing server if running on the same server as Cisco Unified MeetingPlace H.323/SIP IP Gateway.

Note: If you use a hostname, DNS must be enabled to resolve the hostname to an IP address.

hostname


IP address

____________________________


____________________________



Dial Plan Worksheet


About the Dial Plan for the Cisco Unified MeetingPlace H.323/SIP IP Gateway

A dial plan ensures that IP and PSTN calls to and from the Cisco Unified MeetingPlace Audio Server system are directed to the proper endpoints on their respective network. Each type of call has a dial pattern that specifies its call flow to and from the MeetingPlace Audio Server system.


For example, if your Cisco Unified MeetingPlace Audio Server system has both IP and PSTN interfaces, you may want to configure their outdial patterns so that outdials to a PSTN phone will go through the Cisco Unified MeetingPlace Audio Server system PSTN interface. This ensures an outdial to a PSTN phone does not go through the IP network first and then to the PSTN.


For Cisco Unified MeetingPlace Audio Servers systems that have both PSTN and IP interfaces, a dial plan should account for rollover from PSTN to IP ports and vice versa. For example, if you have a Cisco Unified MeetingPlace Audio Server system with 96 IP user licenses and 192 PSTN user licenses, the 97th caller to IP is automatically forwarded to a PSTN port by Cisco Unified Communications Manager through a voice gateway, rather than producing a fast busy signal.


For additional information about mixed-mode configuration, see About Telephony Configurations for Mixed Cisco Unified MeetingPlace Systems and Mixed Cisco Unified MeetingPlace System Configuration Examples.


Dial Plan Worksheet

Use the following worksheet to create a a dial plan

MeetingPlace IP call flow Value

From an IP phone to the IP-gateway server.


If the IP-gateway server is busy, Cisco Unified Communications Manager can forward calls to Cisco Unified MeetingPlace system PSTN through a voice gateway. You must configure Cisco Unified Communications Manager and the voice gateway to route this type of call.

dial pattern____________________


A 4-digit number that does not conflict with a corporate phone extension number scheme.

From a PSTN phone to Cisco Unified MeetingPlace system PSTN.


If Cisco Unified MeetingPlace system PSTN is busy, the PBX or CO can forward calls to the IP-gateway server through Cisco Unified Communications Manager. You must configure the PBX or CO to route this type of call.

dial pattern____________________


A 7- or 10-digit phone number that does not conflict with a corporate phone numbering scheme.

From Cisco Unified MeetingPlace system IP to an IP phone.

dial pattern____________________


Typically, the last four digits of the phone number.

From Cisco Unified MeetingPlace system PSTN to a PSTN phone.

dial pattern____________________


Typically 9, if needed for an outside line, followed by either the 7- or 10-digit phone number.

.

Rating: 0.0/5 (0 votes cast)

Personal tools