Support Tools Troubleshooting: The Support Tools Server fails to connect to the Node Agent - Revision history

Cchetty: 1 revision

2010-03-12T23:53:12Z

1 revision

← Older revision

Revision as of 23:53, 12 March 2010

Masherid at 20:17, 8 March 2010

2010-03-08T20:17:20Z

← Older revision		Revision as of 20:17, 8 March 2010
Line 1:		Line 1:
-	~~{{Template:Required Metadata}}~~
	== The Support Tools Server fails to connect to the Node Agent ==		== The Support Tools Server fails to connect to the Node Agent ==

Line 17:		Line 16:
	Disable IPSec on the Support Tools node agents.		Disable IPSec on the Support Tools node agents.
	# Check that the communication port defined in the registry is the same as is defined in theIPSEC policy.		# Check that the communication port defined in the registry is the same as is defined in theIPSEC policy.
-	</td></tr><tr><td> '''Release''' </td><td>Release 7.5(1)</td></tr><tr><td> '''Associated CDETS #''' </td><td> None. </td></tr></table>	+	</td></tr><tr><td> '''Release''' </td><td>Release 7.5(1) and 8.0</td></tr><tr><td> '''Associated CDETS #''' </td><td> None. </td></tr></table>

	[[Category:Unified ICM/CCE & Hosted, Release 7.5]]		[[Category:Unified ICM/CCE & Hosted, Release 7.5]]
		+	[[Category:Unified CCE, Release 8.0]]

Docwikibot: Bot: Adding {{Template:Required Metadata}}

2009-12-18T19:48:55Z

Bot: Adding {{Template:Required Metadata}}

← Older revision		Revision as of 19:48, 18 December 2009
Line 1:		Line 1:
		+	{{Template:Required Metadata}}
	== The Support Tools Server fails to connect to the Node Agent ==		== The Support Tools Server fails to connect to the Node Agent ==

Cchetty: 1 revision

2009-12-11T07:04:19Z

1 revision

← Older revision

Revision as of 07:04, 11 December 2009

Masherid at 23:37, 9 December 2009

2009-12-09T23:37:38Z

New page

== The Support Tools Server fails to connect to the Node Agent ==

<table border="1"><tr><td> '''Problem Summary''' </td><td>When trying to connect to Node Agents, the following message displays: “Attempt to sendcommand to system: 'ARIPG1A' failed. The specified host could not be contacted by the servicetool. System reported: The requested name is valid, but no data of the requested type was found.”

</td></tr><tr><td> '''Error Message''' </td><td>None.

</td></tr><tr><td> '''Possible Cause''' </td><td>

</td></tr><tr><td> '''Recommended Action''' </td><td>
# Ensure that the Server and Agent services are defined and running.
# Check that the communications port defined is the same on the Server and Agent.
# Check that the IPSEC policy is enabled, *AND* that the IPSEC PSKey is the exact sameon the Server and the Node Agent.
# Check that the Support Server is Windows Server 2003 and not Windows XP. You caninstall the Support Tools server on Windows XP with SP2. However, the Support ToolsNode Agent (installed on an Unified ICM node running window 2003) defaults to installingwith IPSec enabled. Yet, since the Support Tools does not support IPSec on Windows XP,the Support Tools server cannot then connect to the agent(s).
The workaround for the non-support of IPsec on Windows XP is to
do either of thefollowing:Install the Support tools on a Windows Server 2003 server.
Disable IPSec on the Support Tools node agents.
# Check that the communication port defined in the registry is the same as is defined in theIPSEC policy.
</td></tr><tr><td> '''Release''' </td><td>Release 7.5(1)</td></tr><tr><td> '''Associated CDETS #''' </td><td> None. </td></tr></table>

[[Category:Unified ICM/CCE & Hosted, Release 7.5]]