SAF Forwarder with L2 Adjacency Configuration Example - Revision history

Dalin at 15:39, 7 June 2010

2010-06-07T15:39:45Z

← Older revision		Revision as of 15:39, 7 June 2010
Line 12:		Line 12:
	==Related show Commands==		==Related show Commands==

-	show eigrp service-family [ipv4~~\|ipv6]~~ neighbors	+	show eigrp service-family ipv4 neighbors

	Example(s):		Example(s):

Dalin at 22:28, 4 June 2010

2010-06-04T22:28:44Z

← Older revision		Revision as of 22:28, 4 June 2010
Line 14:		Line 14:
	show eigrp service-family [ipv4\|ipv6] neighbors		show eigrp service-family [ipv4\|ipv6] neighbors

-	Example:	+	Example(s):
	[[Image:Show_eigrp_service-family_ipv4_neighbors.jpg‎]]		[[Image:Show_eigrp_service-family_ipv4_neighbors.jpg‎]]

Dalin at 22:27, 4 June 2010

2010-06-04T22:27:57Z

← Older revision		Revision as of 22:27, 4 June 2010
Line 3:		Line 3:
	==Introduction==		==Introduction==

-	This configuration example demonstrates how to configure SAF Forwarders that share a common ~~multiaccess~~ segment.	+	This configuration example demonstrates how to configure SAF Forwarders that share a common multi-access segment.
-	~~Although this example relies on the use of an EIGRP instance, EIGRP as a routing protocol is not required~~	+
-	~~in order for SAF to operate. This is because SAF is responsible for advertising services and not IP prefixes.~~	+
-	~~This means any routing protocol may run with SAF, for example, static, RIP, EIGRP, OSPF and BGP~~.	+

	==Example==		==Example==
Line 17:		Line 14:
	show eigrp service-family [ipv4\|ipv6] neighbors		show eigrp service-family [ipv4\|ipv6] neighbors

		+	Example:
		+	[[Image:Show_eigrp_service-family_ipv4_neighbors.jpg‎]]
		+
		+	==Commonly Asked Question==
		+	Q: Does SAF have to run EIGRP?
		+
		+	A: Although SAF requires that an EIGRP virtual-instance be configured ("SAF-fwdr" in the example above), EIGRP as a routing protocol is not required in order for SAF to operate properly. SAF is responsible for advertising services and not IP prefixes.
		+	SAF can run with any routing protocol (eg: static, RIP, EIGRP, OSPF, BGP).

	==Related Information==		==Related Information==

Dalin at 22:06, 4 June 2010

2010-06-04T22:06:29Z

← Older revision		Revision as of 22:06, 4 June 2010
Line 8:		Line 8:
	This means any routing protocol may run with SAF, for example, static, RIP, EIGRP, OSPF and BGP.		This means any routing protocol may run with SAF, for example, static, RIP, EIGRP, OSPF and BGP.

-	==Example ~~Topology~~==	+	==Example==

	[[Image:Saff_l2.jpg]]		[[Image:Saff_l2.jpg]]

Dalin: New page: {{Template:Required Metadata}} ==Introduction== This configuration example demonstrates how to configure SAF Forwarders that share a common multiaccess segment. Although this example rel...

2010-06-04T18:47:03Z

New page: {{Template:Required Metadata}} ==Introduction== This configuration example demonstrates how to configure SAF Forwarders that share a common multiaccess segment. Although this example rel...

New page

{{Template:Required Metadata}}

==Introduction==

This configuration example demonstrates how to configure SAF Forwarders that share a common multiaccess segment.
Although this example relies on the use of an EIGRP instance, EIGRP as a routing protocol is not required
in order for SAF to operate. This is because SAF is responsible for advertising services and not IP prefixes.
This means any routing protocol may run with SAF, for example, static, RIP, EIGRP, OSPF and BGP.

==Example Topology==

[[Image:Saff_l2.jpg]]

==Related show Commands==

show eigrp service-family [ipv4|ipv6] neighbors

==Related Information==
[http://www.cisco.com/web/psa/products/index.html Technical Support & Documentation - Cisco Systems]
[http://www.cisco.com/go/saf SAF Product Page - Cisco Systems]
[http://www.cisco.com/en/US/docs/ios/saf/configuration/guide/saf_cg.html Cisco IOS SAF Configuration Guide - Cisco Systems]

[[Category: IOS Software and NX-OS Software Configuration Examples]]
[[Category: Router Configuration Examples]]