Pzimmerm: 1 revision

2009-02-05T02:32:10Z

1 revision

← Older revision

Revision as of 02:32, 5 February 2009

Megsunda: /* NTP-D363 Enable or Disable AutoPM */

2009-01-10T08:54:03Z

NTP-D363 Enable or Disable AutoPM

New page

This chapter explains how to enable and view performance monitoring statistics for the Cisco ONS 15454 SDH. Performance monitoring (PM) parameters are used by service providers to gather, store, and set thresholds and to report performance data for early detection of problems. For more PM information, details, and definitions, refer to the ''Cisco ONS 15454 SDH Troubleshooting Guide''.

== Before You Begin ==

Before performing any of the following procedures, investigate all alarms and clear any trouble conditions. Refer to the ''Cisco ONS 15454 SDH Troubleshooting Guide'' as necessary.

This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).
# [[ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance#NTP-D257 Change the PM Display|NTP-D257 Change the PM Display]]-Complete as needed to change the displayed PM counts.
# [[ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance#NTP-D195 Monitor Electrical Performance|NTP-D195 Monitor Electrical Performance]]-Complete as needed to monitor electrical performance.
# [[ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance#NTP-D198 Monitor Ethernet Performance|NTP-D198 Monitor Ethernet Performance]]-Complete as needed to monitor Ethernet performance.
# [[ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance#NTP-D289 Create and Delete Ethernet RMON Thresholds|NTP-D289 Create and Delete Ethernet RMON Thresholds]]-Complete as needed to monitor Ethernet performance.
# [[ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance#NTP-D254 Monitor STM-N Performance|NTP-D254 Monitor STM-N Performance]]-Complete as needed to monitor optical (STM-N) performance.
# [[ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance#NTP-D355 Monitor Multirate Performance|NTP-D355 Monitor Multirate Performance]] -Complete as needed to monitor multirate (MRC-N) performance.
# [[ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance#NTP-D301 Monitor FC_MR-4 Performance|NTP-D301 Monitor FC_MR-4 Performance]]-Complete as needed to monitor FC_MR-4 performance.
# [[ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance#NTP-D302 Create or Delete FC_MR-4 RMON Thresholds|NTP-D302 Create or Delete FC_MR-4 RMON Thresholds]]-Complete as needed to monitor FC_MR-4 performance.
# [[ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance#NTP-D363 Enable or Disable AutoPM|NTP-D363 Enable or Disable AutoPM]]-Complete as needed to enable or disable automatic autonomous performance monitoring (AutoPM) reports.

'''Note: ''' For additional information regarding PM parameters, refer to ITU G.826, Telcordia GR-820-CORE, Telcordia GR-499-CORE, and Telcordia GR-253-CORE.

== NTP-D257 Change the PM Display ==

{| border = 1
|-
|

'''Purpose'''
|

This procedure changes the display of PM counts by selecting drop-down list or radio button options in the Performance window.
|-
|

'''Tools/Equipment '''
|

None
|-
|

'''Prerequisite Procedures'''
|

Before you monitor performance, be sure you have created the appropriate circuits and provisioned the card according to your specifications. For more information, see [[ONS 15454 SDH Procedure Guide R8.5.1 -- Create Circuits and Low-Order Tunnels#Create Circuits and Low-Order Tunnels|Create Circuits and Low-Order Tunnels]] and [[ONS 15454 SDH Procedure Guide R8.5.1 -- Change Card Settings#Change Card Settings|Change Card Settings]].
|-
|

'''Required/As Needed'''
|

As needed
|-
|

'''Onsite/Remote'''
|

Onsite or remote
|-
|

'''Security Level'''
|

Retrieve or higher
|}

# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D1 to D99#DLP-D60 Log into CTC|"DLP-D60 Log into CTC"]] task at the node that you want to monitor. If you are already logged in, continue with Step 2.
# In node view, double-click the electrical, Ethernet, optical (STM-N), or multirate transport card where you want to view PM counts. The card view appears.
# As needed, use the following tasks to change the display of PM counts:
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D100 to D199#DLP-D124 Refresh PM Counts at 15-Minute Intervals|DLP-D124 Refresh PM Counts at 15-Minute Intervals]]
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D100 to D199#DLP-D125 Refresh PM Counts at One-Day Intervals|DLP-D125 Refresh PM Counts at One-Day Intervals]]
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D200 to D299#DLP-D259 Refresh Ethernet PM Counts at a Different Time Interval|DLP-D259 Refresh Ethernet PM Counts at a Different Time Interval]]
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D100 to D199#DLP-D126 View Near-End PM Counts|DLP-D126 View Near-End PM Counts]]
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D100 to D199#DLP-D127 View Far-End PM Counts|DLP-D127 View Far-End PM Counts]]
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D400 to D499#DLP-D458 Monitor PM Counts for a Selected Signal|DLP-D458 Monitor PM Counts for a Selected Signal]]
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D100 to D199#DLP-D129 Reset Current PM Counts|DLP-D129 Reset Current PM Counts]]
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D400 to D499#DLP-D459 Clear Selected PM Counts|DLP-D459 Clear Selected PM Counts]]
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D200 to D299#DLP-D286 Clear All PM Thresholds|DLP-D286 Clear All PM Thresholds]]
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D400 to D499#DLP-D457 Refresh E-Series and G-Series Ethernet PM Counts|DLP-D457 Refresh E-Series and G-Series Ethernet PM Counts]]
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D200 to D299#DLP-D260 Set Auto-Refresh Interval for Displayed PM Counts|DLP-D260 Set Auto-Refresh Interval for Displayed PM Counts]]
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D200 to D299#DLP-D261 Refresh PM Counts for a Different Port|DLP-D261 Refresh PM Counts for a Different Port]]
#: '''Stop. You have completed this procedure.'''

== NTP-D195 Monitor Electrical Performance ==

{| border = 1
|-
|

'''Purpose'''
|

This procedure enables you to view node near-end or far-end performance during selected time intervals on an electrical card and port to detect possible performance problems.
|-
|

'''Tools/Equipment '''
|

None
|-
|

'''Prerequisite Procedures'''
|

Before you monitor performance, be sure you have created the appropriate circuits and provisioned the card according to your specifications. For more information, see [[ONS 15454 SDH Procedure Guide R8.5.1 -- Create Circuits and Low-Order Tunnels#Create Circuits and Low-Order Tunnels|Create Circuits and Low-Order Tunnels]] and [[ONS 15454 SDH Procedure Guide R8.5.1 -- Change Card Settings#Change Card Settings|Change Card Settings]].
|-
|

'''Required/As Needed'''
|

As needed
|-
|

'''Onsite/Remote'''
|

Onsite or remote
|-
|

'''Security Level'''
|

Retrieve or higher
|}

# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D1 to D99#DLP-D60 Log into CTC|"DLP-D60 Log into CTC"]] task at the node that you want to monitor. If you are already logged in, continue with Step 2.
# In node view, double-click the electrical card where you want to view PM counts. The card view appears.
# Click the '''Performance''' tab ([[ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance#Figure 8-1: Viewing Performance Monitoring Information|Figure 8-1]]).

===== Figure 8-1: Viewing Performance Monitoring Information=====

[[Image:102002.jpg]]
<ol start=4><li>View the PM parameter names that appear on the left portion of the window in the Param column. The PM parameter values appear on the right portion of the window in the Curr (current), and Prev-''n'' (previous) columns. For PM parameter definitions, refer to the "Performance Monitoring" chapter in the ''Cisco ONS 15454 SDH Reference Manual''.
: To refresh, reset, or clear PM counts, see the [[ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance#NTP-D257 Change the PM Display|NTP-D257 Change the PM Display]].
: '''Stop. You have completed this procedure.'''</li></ol>

== NTP-D198 Monitor Ethernet Performance ==

{| border = 1
|-
|

'''Purpose'''
|

This procedure enables you to view node transmit and receive performance during selected time intervals on an Ethernet card and port to detect possible performance problems.
|-
|

'''Tools/Equipment '''
|

None
|-
|

'''Prerequisite Procedures'''
|

Before you monitor performance, be sure you have created the appropriate circuits and provisioned the card according to your specifications. For more information, see [[ONS 15454 SDH Procedure Guide R8.5.1 -- Create Circuits and Low-Order Tunnels#Create Circuits and Low-Order Tunnels|Create Circuits and Low-Order Tunnels]] and [[ONS 15454 SDH Procedure Guide R8.5.1 -- Change Card Settings#Change Card Settings|Change Card Settings]].
|-
|

'''Required/As Needed'''
|

As needed
|-
|

'''Onsite/Remote'''
|

Onsite or remote
|-
|

'''Security Level'''
|

Retrieve or higher
|}

# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D1 to D99#DLP-D60 Log into CTC|"DLP-D60 Log into CTC"]] task at the node that you want to monitor. If you are already logged in, continue with Step 2.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D200 to D299#DLP-D256 View Ethernet Statistics PM Parameters|"DLP-D256 View Ethernet Statistics PM Parameters"]] task.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D200 to D299#DLP-D257 View Ethernet Utilization PM Parameters|"DLP-D257 View Ethernet Utilization PM Parameters"]] task.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D200 to D299#DLP-D258 View Ethernet History PM Parameters|"DLP-D258 View Ethernet History PM Parameters"]] task.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D300 to D399#DLP-D348 View ML-Series Ether Ports PM Parameters|"DLP-D348 View ML-Series Ether Ports PM Parameters"]] task.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D300 to D399#DLP-D349 View ML-Series POS Ports PM Parameters|"DLP-D349 View ML-Series POS Ports PM Parameters"]] task.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D200 to D299#DLP-D228 View ML-Series RPR Span PM Parameters|"DLP-D228 View ML-Series RPR Span PM Parameters"]] task.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D100 to D199#DLP-D188 View CE-Series Ethernet and POS Ports Statistics PM Parameters|"DLP-D188 View CE-Series Ethernet and POS Ports Statistics PM Parameters"]] task.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D100 to D199#DLP-D190 View CE-Series Ethernet and POS Ports Utilization PM Parameters|"DLP-D190 View CE-Series Ethernet and POS Ports Utilization PM Parameters"]] task.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D100 to D199#DLP-D192 View CE-Series Ethernet and POS Ports History PM Parameters|"DLP-D192 View CE-Series Ethernet and POS Ports History PM Parameters"]] task.
#: '''Stop. You have completed this procedure.'''

== NTP-D289 Create and Delete Ethernet RMON Thresholds ==

{| border = 1
|-
|

'''Purpose'''
|

This procedure creates or deletes Ethernet remote monitoring (RMON) thresholds for the ONS 15454 SDH.
|-
|

'''Tools/Equipment'''
|

None
|-
|

'''Prerequisite Procedures'''
|

None
|-
|

'''Required/As Needed'''
|

As needed
|-
|

'''Onsite/Remote'''
|

Onsite or remote
|-
|

'''Security Level'''
|

Provisioning or higher
|}

# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D1 to D99#DLP-D60 Log into CTC|"DLP-D60 Log into CTC"]] task. If you are already logged in, continue with Step 2.
# Perform any of the following tasks as needed:
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D400 to D499#DLP-D441 Create Ethernet RMON Alarm Thresholds|DLP-D441 Create Ethernet RMON Alarm Thresholds]]
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D400 to D499#DLP-D436 Delete Ethernet RMON Alarm Thresholds|DLP-D436 Delete Ethernet RMON Alarm Thresholds]]
#: '''Stop. You have completed this procedure.'''

== NTP-D254 Monitor STM-N Performance ==

{| border = 1
|-
|

'''Purpose'''
|

This procedure enables you to view node near-end or far-end performance during selected time intervals on an STM-N card and port to detect possible performance problems.
|-
|

'''Tools/Equipment '''
|

None
|-
|

'''Prerequisite Procedures'''
|

Before you monitor performance, be sure you have created the appropriate circuits and provisioned the card according to your specifications. For more information, see [[ONS 15454 SDH Procedure Guide R8.5.1 -- Create Circuits and Low-Order Tunnels#Create Circuits and Low-Order Tunnels|Create Circuits and Low-Order Tunnels]] and [[ONS 15454 SDH Procedure Guide R8.5.1 -- Change Card Settings#Change Card Settings|Change Card Settings]].
|-
|

'''Required/As Needed'''
|

As needed
|-
|

'''Onsite/Remote'''
|

Onsite or remote
|-
|

'''Security Level'''
|

Retrieve or higher
|}

# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D1 to D99#DLP-D60 Log into CTC|"DLP-D60 Log into CTC"]] task at the node that you want to monitor. If you are already logged in, continue with Step 2.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D100 to D199#DLP-D121 Enable Pointer Justification Count Performance Monitoring|"DLP-D121 Enable Pointer Justification Count Performance Monitoring"]] task as needed to enable or disable clock synchronization monitoring.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D100 to D199#DLP-D122 Enable Intermediate Path Performance Monitoring|"DLP-D122 Enable Intermediate Path Performance Monitoring"]] task as needed to enable or disable monitoring of VC4 traffic through intermediate nodes.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D400 to D499#DLP-D421 View STM-N PM Parameters|"DLP-D421 View STM-N PM Parameters"]] task.
#:'''Note: ''' To refresh, reset, or clear PM counts, see the [[ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance#NTP-D257 Change the PM Display|NTP-D257 Change the PM Display]].
#: '''Stop. You have completed this procedure.'''

== NTP-D355 Monitor Multirate Performance ==

{| border = 1
|-
|

'''Purpose'''
|

This procedure enables you to view node near-end or far-end performance during selected time intervals on an MRC-N card and port to detect possible performance problems.
|-
|

'''Tools/Equipment '''
|

None
|-
|

'''Prerequisite Procedures'''
|

Before you monitor performance, be sure you have created the appropriate circuits and provisioned the card according to your specifications. For more information, see [[ONS 15454 SDH Procedure Guide R8.5.1 -- Create Circuits and Low-Order Tunnels#Create Circuits and Low-Order Tunnels|Create Circuits and Low-Order Tunnels]] and [[ONS 15454 SDH Procedure Guide R8.5.1 -- Change Card Settings#Change Card Settings|Change Card Settings]].
|-
|

'''Required/As Needed'''
|

As needed
|-
|

'''Onsite/Remote'''
|

Onsite or remote
|-
|

'''Security Level'''
|

Retrieve or higher
|}

# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D1 to D99#DLP-D60 Log into CTC|"DLP-D60 Log into CTC"]] task at the node that you want to monitor. If you are already logged in, continue with Step 2.
# In node view, double-click the multirate card where you want to view PM counts. The card view appears.
# Click the '''Performance''' tab.
# In the Port drop-down list, choose the port you want to monitor.
# Click '''Refresh'''.
# View the PM parameter names that appear in the Param column. The PM parameter values appear in the Curr (current), and Prev-''n'' (previous) columns. For PM parameter definitions, refer to the "Performance Monitoring" chapter in the ''Cisco ONS 15454 SDH Reference Manual''.
# To monitor another port on a multiport card, choose another port from the Port drop-down list and click '''Refresh'''.
#: '''Note: ''' To refresh, reset, or clear PM counts, see the [[ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance#NTP-D257 Change the PM Display|NTP-D257 Change the PM Display]].
#: '''Stop. You have completed this procedure.'''

== NTP-D301 Monitor FC_MR-4 Performance ==

{| border = 1
|-
|

'''Purpose'''
|

This procedure enables you to view node transmit and receive performance during selected time intervals on an FC_MR-4 card and port to detect possible performance problems.
|-
|

'''Tools/Equipment '''
|

None
|-
|

'''Prerequisite Procedures'''
|

Before you monitor performance, be sure you have created the appropriate circuits and provisioned the card according to your specifications. For more information, see [[ONS 15454 SDH Procedure Guide R8.5.1 -- Create Circuits and Low-Order Tunnels#Create Circuits and Low-Order Tunnels|Create Circuits and Low-Order Tunnels]] and [[ONS 15454 SDH Procedure Guide R8.5.1 -- Change Card Settings#Change Card Settings|Change Card Settings]].
|-
|

'''Required/As Needed'''
|

As needed
|-
|

'''Onsite/Remote'''
|

Onsite or remote
|-
|

'''Security Level'''
|

Retrieve or higher
|}

# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D1 to D99#DLP-D60 Log into CTC|"DLP-D60 Log into CTC"]] task at the node that you want to monitor. If you are already logged in, continue with Step 2.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D400 to D499#DLP-D460 View FC_MR-4 Statistics PM Parameters|"DLP-D460 View FC_MR-4 Statistics PM Parameters"]] task.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D400 to D499#DLP-D461 View FC_MR-4 Utilization PM Parameters|"DLP-D461 View FC_MR-4 Utilization PM Parameters"]] task.
# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D400 to D499#DLP-D462 View FC_MR-4 History PM Parameters|"DLP-D462 View FC_MR-4 History PM Parameters"]] task.
#: '''Stop. You have completed this procedure.'''

== NTP-D302 Create or Delete FC_MR-4 RMON Thresholds ==

{| border = 1
|-
|

'''Purpose'''
|

This procedure creates or deletes FC_MR-4 RMON thresholds for the ONS 15454 SDH.
|-
|

'''Tools/Equipment'''
|

None
|-
|

'''Prerequisite Procedures'''
|

None
|-
|

'''Required/As Needed'''
|

As needed
|-
|

'''Onsite/Remote'''
|

Onsite or remote
|-
|

'''Security Level'''
|

Provisioning or higher
|}

# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D1 to D99#DLP-D60 Log into CTC|"DLP-D60 Log into CTC"]] task. If you are already logged in, continue with Step 2.
# Perform any of the following tasks as needed:
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D400 to D499#DLP-D465 Create FC_MR-4 RMON Alarm Thresholds|DLP-DLP-D465 Create FC_MR-4 RMON Alarm Thresholds]]
#* [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D400 to D499#D466 Delete FC_MR-4 RMON Alarm Thresholds|DLP-D466 Delete FC_MR-4 RMON Alarm Thresholds]]
#: '''Stop. You have completed this procedure.'''

== NTP-D363 Enable or Disable AutoPM ==

{| border = 1
|-
|

'''Purpose'''
|

This procedure allows you to enable or disable automatic autonomous performance monitoring (AutoPM) reports.
|-
|

'''Tools/Equipment'''
|

None
|-
|

'''Prerequisite Procedures'''
|

None
|-
|

'''Required/As Needed'''
|

As needed
|-
|

'''Onsite/Remote'''
|

Onsite or remote
|-
|

'''Security Level'''
|

Provisioning or higher
|}

# Complete the [[ONS 15454 SDH Procedure Guide R8.5.1 -- DLPs D1 to D99#DLP-D60 Log into CTC|"DLP-D60 Log into CTC"]] task. If you are already logged in, continue with Step 2.
# Click the '''Provisioning''' > '''Defaults '''tabs.
# In the Defaults Selector area, click '''NODE > General''' and choose '''NODE.general.AutoPM'''.
# In the Default Value field, select '''True''' to enable AutoPM.
# Click '''Apply'''.
#: Follow Steps 1 through 5 to disable AutoPM. Select '''False''' in the Default Value field in Step 4 before proceeding to Step 5.
#: '''Stop. You have completed this procedure.'''

ONS 15454 SDH Procedure Guide R8.5.1 -- Monitor Performance - Revision history

Pzimmerm: 1 revision

Megsunda: /* NTP-D363 Enable or Disable AutoPM */