ONS 15454 SDH Procedure Guide R8.5.1 -- Change Node Settings

From DocWiki

(Difference between revisions)
Jump to: navigation, search
m (1 revision)
 

Latest revision as of 02:32, 5 February 2009

This chapter explains how to modify node provisioning for the Cisco ONS 15454 SDH. To provision a new node, see Turn Up a Node. To change default network element (NE) settings and to view a list of those settings, refer to the "Network Element Defaults" appendix in the Cisco ONS 15454 SDH Reference Manual.

Contents

Before You Begin

Before performing the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS 15454 SDH Troubleshooting Guide as necessary.

This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).

  1. NTP-D81 Change Node Management Information-As needed, complete this procedure to change the node name, contact information, latitude, longitude, date, time, and login legal disclaimer.
  2. NTP-D201 Change CTC Network Access-As needed, complete these procedures to change the IP address, default router, subnet mask, network configuration settings, and static routes.
  3. NTP-D327 Modify OSI Provisioning-Complete this procedure as needed to modify Open System Interconnection (OSI) parameters including the OSI routing mode, Target Identifier Address Resolution Protocol (TARP), routers, subnets, and IP-over-CLNS tunnels.
  4. NTP-D202 Customize the CTC Network View-As needed, complete this procedure to create domains and customize the appearance of the network map, including specifying a different default map, creating domains, selecting your own map or image, and changing the background color.
  5. NTP-D203 Modify or Delete Card Protection Settings-Complete as needed.
  6. NTP-D277 Modify or Delete Communications Channel Terminations-Complete as needed to modify or delete regenerator section data communications channel (RS-DCC) and multiplex section data communications channel (MS-DCC) terminations, and to delete provisionable patchcords.
  7. NTP-D85 Change Node Timing-Complete as needed.
  8. NTP-D205 Modify Users and Change Security-Complete as needed.
  9. NTP-D87 Change SNMP Settings-Complete as needed.

NTP-D81 Change Node Management Information

Purpose

This procedure changes the node name, date, time, contact information, or the login legal disclaimer.

Tools/Equipment

None

Prerequisite Procedures

NTP-D316 Set Up Name, Date, Time, and Contact Information

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser only

  1. Complete the "DLP-D60 Log into CTC" task at the node where you want to change the settings. If you are already logged in, continue with Step 2.
  2. Complete the NTP-D108 Back Up the Database.
  3. In the node view, click the Provisioning > General tabs.
  4. Complete the "DLP-D140 Change the Node Name, Date, Time, and Contact Information" task.
  5. Complete the "DLP-D265 Change the Login Legal Disclaimer" task, as needed.
  6. After confirming the changes, complete the NTP-D108 Back Up the Database.
    Stop. You have completed this procedure.

NTP-D201 Change CTC Network Access

Purpose

This procedure changes essential network information, including IP settings, static routes, and OSPF options.

Tools/Equipment

None

Prerequisite Procedures

NTP-D169 Set Up CTC Network Access

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser only

Note: Additional ONS 15454 SDH networking information and procedures, including IP addressing examples, static route scenarios, Open Shortest Path First (OSPF) protocol, and routing information protocol options are provided in the "Management Network Connectivity" chapter of the Cisco ONS 15454 SDH Reference Manual.

  1. Complete the "DLP-D60 Log into CTC" task. If you are already logged in, continue with Step 2.
  2. Complete the NTP-D108 Back Up the Database.
  3. Perform any of the following tasks as needed:
  4. Complete the NTP-D108 Back Up the Database.
    Stop. You have completed this procedure.

NTP-D327 Modify OSI Provisioning

Purpose

This procedure modifies the ONS 15454 OSI parameters including the OSI routing mode, TARP, routers, subnets, and IP-over-CLNS tunnels.

Tools/Equipment

None

Prerequisite Procedures

NTP-D326 Provision OSI

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

Note: Additional information about the ONS 15454 implementation of OSI is provided in the "Management Network Connectivity" chapter of the Cisco ONS 15454 SDH Reference Manual.

  1. Complete the "DLP-D60 Log into CTC" task. If you are already logged in, continue with Step 2.
  2. Complete the NTP-D108 Back Up the Database.
  3. Perform any of the following tasks as needed:
  4. Complete the NTP-D108 Back Up the Database.
    Stop. You have completed this procedure.

NTP-D202 Customize the CTC Network View

Purpose

This procedure modifies the CTC network view, including grouping nodes into domains for a less-cluttered display, changing the network view background color, and using a custom image for the network view background.

Tools/Equipment

None

Prerequisite Procedures

None

Required/As needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

  1. Complete the "DLP-D60 Log into CTC" task. If you are already logged in, continue with Step 2.
  2. Complete the following tasks, as needed:
    Stop. You have completed this procedure.

NTP-D203 Modify or Delete Card Protection Settings

Purpose

This procedure modifies or deletes card protection settings.

Tools/Equipment

None

Prerequisite Procedures

NTP-D170 Create Protection Groups

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

Caution! Modifying and deleting protection groups can be service affecting.

  1. Compete the "DLP-D60 Log into CTC" task. If you are already logged in, continue with Step 2.
  2. Complete the NTP-D108 Back Up the Database.
  3. Perform any of the following tasks as needed:
  4. Complete the NTP-D108 Back Up the Database.
    Stop. You have completed this procedure.

NTP-D277 Modify or Delete Communications Channel Terminations

Purpose

This procedure changes or deletes RS-DCC or MS-DCC terminations on the ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

DLP-D363 Provision Regenerator-Section DCC Terminations

DLP-D364 Provision Multiplex-Section DCC Terminations

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

  1. Complete the "DLP-D60 Log into CTC" task. If you are already logged in, continue with Step 2.
  2. Click the Provisioning > Comm Channels tabs.
  3. Complete the following tasks to modify communication channel terminations, as needed:
  4. Complete the following tasks to delete communication channel terminations, as needed:
    Stop. You have completed this procedure.

NTP-D85 Change Node Timing

Purpose

This procedure changes the SDH timing settings for the ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

NTP-D28 Set Up Timing

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

  1. Complete the "DLP-D60 Log into CTC" task. If you are already logged in, continue with Step 2.
  2. Complete the NTP-D108 Back Up the Database.
  3. As needed, complete the "DLP-D157 Change the Node Timing Source" task.
  4. If you need to change any internal timing settings, complete the "DLP-D70 Set Up Internal Timing" task for the settings you need to modify.
    Caution! Internal timing is Stratum 3 and not intended for permanent use. All ONS 15454 SDHs should be timed to a Stratum 2 or better primary reference source.
  5. If you need to verify timing after removing a node from an multiplex section-shared protection ring (MS-SPRing) or subnet connection protection (SNCP) ring, see the "DLP-D195 Verify Timing in a Reduced Ring" task.
  6. Complete the NTP-D108 Back Up the Database.
    Stop. You have completed this procedure.

NTP-D205 Modify Users and Change Security

Purpose

This procedure modifies user and security properties for the ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

NTP-D30 Create Users and Assign Security

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

  1. Complete the "DLP-D60 Log into CTC" task. If you are already logged in, continue with Step 2.
  2. Complete the NTP-D108 Back Up the Database.
  3. Perform any of the following tasks as needed:
  4. Complete the NTP-D108 Back Up the Database.
    Stop. You have completed this procedure.

NTP-D87 Change SNMP Settings

Purpose

This procedure modifies SNMP settings for the ONS 15454 SDH.

Tools/Equipment

None

Prerequisite Procedures

NTP-D171 Set Up SNMP

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser only

  1. Complete the "DLP-D60 Log into CTC" task. If you are already logged in, continue with Step 2.
  2. Complete the NTP-D108 Back Up the Database.
  3. Perform any of the following tasks as needed:
  4. Complete the NTP-D108 Back Up the Database.
    Stop. You have completed this procedure.

Rating: 0.0/5 (0 votes cast)

Personal tools