Pzimmerm: added metadata

2012-10-16T20:38:16Z

added metadata

← Older revision		Revision as of 20:38, 16 October 2012
Line 1:		Line 1:
	{{Template:Required Metadata}}		{{Template:Required Metadata}}
		+	<meta name="keywords" content="internetworking, hssi, dte, dec"></meta>
	The High-Speed Serial Interface (HSSI) is a DTE/DCE interface that was developed by Cisco Systems and T3plus Networking to address the need for high-speed communication over WAN links. The HSSI specification is available to any organization wanting to implement HSSI.		The High-Speed Serial Interface (HSSI) is a DTE/DCE interface that was developed by Cisco Systems and T3plus Networking to address the need for high-speed communication over WAN links. The HSSI specification is available to any organization wanting to implement HSSI.

Docwikibot: Bot: Adding {{Template:Required Metadata}}

2009-12-17T21:52:15Z

Bot: Adding {{Template:Required Metadata}}

← Older revision		Revision as of 21:52, 17 December 2009
Line 1:		Line 1:
		+	{{Template:Required Metadata}}
	The High-Speed Serial Interface (HSSI) is a DTE/DCE interface that was developed by Cisco Systems and T3plus Networking to address the need for high-speed communication over WAN links. The HSSI specification is available to any organization wanting to implement HSSI.		The High-Speed Serial Interface (HSSI) is a DTE/DCE interface that was developed by Cisco Systems and T3plus Networking to address the need for high-speed communication over WAN links. The HSSI specification is available to any organization wanting to implement HSSI.

Bhhegde: 1 revision

2009-06-05T04:10:51Z

1 revision

← Older revision

Revision as of 04:10, 5 June 2009

Bhhegde: /* HSSI Interface Basics */

2009-05-20T08:53:07Z

HSSI Interface Basics

New page

The High-Speed Serial Interface (HSSI) is a DTE/DCE interface that was developed by Cisco Systems and T3plus Networking to address the need for high-speed communication over WAN links. The HSSI specification is available to any organization wanting to implement HSSI.

{| align="right" border="1"
|align="center"|'''Guide Contents'''
|-
|[[Internetworking Technology Handbook# Internetworking Basics| Internetworking Basics]] [[Internetworking Technology Handbook# LAN Technologies| LAN Technologies]] [[ Internetworking Technology Handbook # WAN Technologies | WAN Technologies]] [[ Internetworking Technology Handbook # Internet Protocols | Internet Protocols]] [[ Internetworking Technology Handbook # Bridging and Switching | Bridging and Switching]] [[ Internetworking Technology Handbook # Routing | Routing]] [[ Internetworking Technology Handbook # Network Management | Network Management]] [[ Internetworking Technology Handbook # Voice/Data Integration Technologies| Voice/Data Integration Technologies]] [[ Internetworking Technology Handbook # Wireless Technologies| Wireless Technologies]] [[ Internetworking Technology Handbook # Cable Access Technologies| Cable Access Technologies]] [[ Internetworking Technology Handbook # Dial-up Technology| Dial-up Technology]] [[ Internetworking Technology Handbook # Security Technologies| Security Technologies]] [[ Internetworking Technology Handbook # Quality of Service Networking| Quality of Service Networking]] [[ Internetworking Technology Handbook # Network Caching Technologies| Network Caching Technologies]] [[ Internetworking Technology Handbook # IBM Network Management| IBM Network Management]] [[ Internetworking Technology Handbook # Multiservice Access Technologies| Multiservice Access Technologies]]
|}

== HSSI Interface Basics ==
HSSI defines both electrical and physical interfaces on DTE and DCE devices. It operates at the physical layer of the OSI reference model.

HSSI technical characteristics are summarized in [[High-Speed Serial Interface#Table: HSSI Technical Characteristics|Table: HSSI Technical Characteristics]].

===== Table: HSSI Technical Characteristics=====

{| border = 1
|-
|'''Characteristic'''

|'''Value'''

|-
|

Maximum signaling rate
|

52 Mbps
|-
|

Maximum cable length
|

50 feet
|-
|

Number of connector points
|

50
|-
|

Interface
|

DTE-DCE
|-
|

Electrical technology
|

Differential ECL
|-
|

Typical power consumption
|

610 mW
|-
|

Topology
|

Point-to-point
|-
|

Cable type
|

Shielded twisted-pair wire
|}

The maximum signaling rate of HSSI is 52 Mbps. At this rate, HSSI can handle the T3 speeds (45 Mbps) of many of today's fast WAN technologies, as well as the Optical Channel-1 (OC-1) speeds (52 Mbps) of the synchronous digital hierarchy (SDH). In addition, HSSI easily can provide high-speed connectivity between LANs, such as Token Ring and Ethernet.

The use of differential emitter-coupled logic (ECL) helps HSSI achieve high data rates and low noise levels. ECL has been used in Cray computer system interfaces for years and is specified by the ANSI High-Performance Parallel Interface (HIPPI) communications standard for supercomputer LAN communications. ECL is an off-the-shelf technology that permits excellent retiming on the receiver, resulting in reliable timing margins.

HSSI uses a subminiature, FCC-approved 50-pin connector that is smaller than its V.35 counterpart. To reduce the need for male-male and female-female adapters, HSSI cable connectors are specified as male. The HSSI cable uses the same number of pins and wires as the Small Computer Systems Interface 2 (SCSI-2) cable, but the HSSI electrical specification is more concise.

== HSSI Operation ==
The flexibility of the HSSI clock and data-signaling protocol makes user (or vendor) bandwidth allocation possible. The DCE controls the clock by changing its speed or by deleting clock pulses. In this way, the DCE can allocate bandwidth between applications. For example, a PBX may require a particular amount of bandwidth, a router another amount, and a channel extender a third amount. Bandwidth allocation is key to making T3 and other broadband services affordable and popular.

HSSI assumes a peer-to-peer intelligence in the DCE and DTE. The control protocol is simplified, with just two control signals required ("DTE available" and "DCE available"). Both signals must be asserted before the data circuit can become valid. The DCE and DTE are expected to be capable of managing the networks behind their interfaces. Reducing the number of control signals improves circuit reliability by reducing the number of circuits that can fail.
=== Loopback Tests ===
HSSI provides four loopback tests, which are illustrated in [[High-Speed Serial Interface#Figure: HSSI Supports Four Loopback Tests|Figure: HSSI Supports Four Loopback Tests]]. The first provides a local cable test as the signal loops back after it reaches the DTE port. The second test reaches the line port of the local DCE. The third test reaches the line port of the remote DCE. Finally, the fourth test is a DCE-initiated test of the DTE's DCE port.

=====Figure: HSSI Supports Four Loopback Tests=====

[[image:CT841101.jpg]]

== Summary ==
HSSI is an interface technology that was developed by Cisco Systems and T3plus Networking in the late 1990s to fill the need for a high-speed data communication solution over WAN links. It uses differential emitter-coupled logic (ECL), which provides high-speed data transfer with low noise levels. HSSI pin connectors are significantly smaller than pin connectors for competing technologies. The HSSI cable uses the same number of pins and wires as the Small Computer Systems Interface 2 (SCSI-2) cable, but its electrical specification is more concise. HSSI makes bandwidth resources easy to allocate, making T3 and other broadband services available and affordable. HSSI requires the presence of only two control signals, making it highly reliable because there are fewer circuits that can fail. HSSI performs four loopback tests for reliability.
== Review Questions ==

'''Q''' - ''Name at least three benefits of implementing HSSI technology in a network.''

'''A''' - Benefits include these:
HSSI provides high-speed data communication over WAN and LAN links.

HSSI uses differential emitter-coupled logic (ECL), which provides high-speed data transfer with low noise levels.

HSSI uses a subminiature FCC-approved 50-pin connector that is smaller than its V.35 competitor.

The HSSI cable uses the same number of pins and wires as the Small Computer Systems Interface 2 (SCSI-2) cable, but the HSSI electrical specification is more concise.

HSSI makes bandwidth resources easy to allocate, making T3 and other broadband services available and affordable.

HSSI requires the presence of only two control signals ("DTE available" and "DCE available"), making it highly reliable because there are fewer circuits that can fail.

HSSI performs four loopback tests for reliability.

'''Q''' - ''Name the four loopback tests that HSSI performs. ''

'''A''' - Cable test, DCE test, Telco line test, DTE test.

[[Category:IOS Technology Handbook]]

High-Speed Serial Interface - Revision history

Pzimmerm: added metadata

Docwikibot: Bot: Adding {{Template:Required Metadata}}

Bhhegde: 1 revision

Bhhegde: /* HSSI Interface Basics */