Annekim: /* Table: Fields for SIP Trunk Security Profile Configuration */

2012-05-04T17:08:22Z

Table: Fields for SIP Trunk Security Profile Configuration

← Older revision		Revision as of 17:08, 4 May 2012
Line 115:		Line 115:
	\|		\|

-	We recommend that you select '''~~TCP~~'''.	+	We recommend that you select '''UDP'''.
	\|-		\|-
	\|		\|
Line 143:		Line 143:


-	:6. Select '''Save'''.	+	:6. Select '''Save'''.
-		+

	===== Related Topics =====		===== Related Topics =====

Annekim: /* Configuring Cisco Unified Communications Manager: Music On Hold */ added note that MoH task is not required for cucm 7.x and later

2011-02-09T22:16:42Z

Configuring Cisco Unified Communications Manager: Music On Hold: added note that MoH task is not required for cucm 7.x and later

← Older revision		Revision as of 22:16, 9 February 2011
Line 236:		Line 236:
	* Adding all phones for which you want to enable music on hold to the Media Resource Group List that contains the music on hold Media Resource Group.		* Adding all phones for which you want to enable music on hold to the Media Resource Group List that contains the music on hold Media Resource Group.
	* Making sure that the music on hold Media Resource Group List is ''not'' assigned to the SIP trunk that connects Cisco Unified Communications Manager to Cisco Unified MeetingPlace.		* Making sure that the music on hold Media Resource Group List is ''not'' assigned to the SIP trunk that connects Cisco Unified Communications Manager to Cisco Unified MeetingPlace.
		+
		+
		+	'''Note:''' This procedure is not required if you are using Cisco Unified Communications Manager Release 7.x or later since these systems use an isFocus flag to suppress music on hold.

MeetingPlace Moderator: 1 revision

2010-07-02T17:12:24Z

1 revision

← Older revision

Revision as of 17:12, 2 July 2010

MeetingPlace Moderator: /* Configuring How Cisco Unified MeetingPlace Displays an Endpoint as a Meeting Participant */

2010-07-01T18:01:23Z

Configuring How Cisco Unified MeetingPlace Displays an Endpoint as a Meeting Participant

New page

'''Main page:''' [[Cisco Unified MeetingPlace, Release 8.0]]

'''Up one level:''' [[Cisco Unified MeetingPlace Release 8.0 -- Integrations|Integrations]]

'''Note: ''' The names for Cisco Unified CallManager Releases 4.3, 5.1, and 6.0 have been changed to Cisco Unified Communications Manager Releases 4.3, 5.1, and 6.0.

The names of Cisco Unified CallManager Releases 4.0, 4.1, 4.2, and 5.0 have ''not'' changed and remain the same.

We recommend that you use Cisco Unified Communications Manager to provide call-control and other services for Cisco Unified MeetingPlace and your IP telephony network.

{| border = 1
|-
!Integration Options
!Where to Find Information
|-
|

Call control
|

[[Cisco Unified MeetingPlace Release 8.0 -- Configuring Call Control for Cisco Unified MeetingPlace#Configuring Call Control for Cisco Unified MeetingPlace|Configuring Call Control for Cisco Unified MeetingPlace]] module
|-
|

Directory service
|

[[Cisco Unified MeetingPlace Release 8.0 -- Configuring Cisco Unified MeetingPlace Directory Service#Configuring Cisco Unified MeetingPlace Directory Service|Configuring Cisco Unified MeetingPlace Directory Service]] module
|-
|

Cisco Unified MeetingPlace PhoneView
|

[[Cisco Unified MeetingPlace Release 8.0 -- Integrating Cisco Unified MeetingPlace with Cisco Unified IP Phones#Integrating Cisco Unified MeetingPlace with Cisco Unified IP Phones|Integrating Cisco Unified MeetingPlace with Cisco Unified IP Phones]] module
|}

'''Note: ''' Cisco Unified MeetingPlace is not compatible with the call preservation feature of Cisco Unified Communications Manager. The call preservation feature allows a call to stay up after the signaling path is lost, for example because of a Cisco Unified Communications Manager node restart. When a call enters that state, Cisco Unified MeetingPlace drops the call at the next session refresh, which occurs within 15 minutes. In the meantime, the preserved call can prevent the user from signing in to Cisco Unified MeetingPlace over the phone or dialing out from the web user portal.

This module also describes certain Cisco Unified Communications Manager settings that can affect Cisco Unified MeetingPlace:
* [[Cisco Unified MeetingPlace Release 8.0 -- Integrating Cisco Unified MeetingPlace with Cisco Unified Communications Manager#Configuring a SIP Trunk Security Profile in Cisco Unified Communications Manager for Cisco Unified MeetingPlace|Configuring a SIP Trunk Security Profile in Cisco Unified Communications Manager for Cisco Unified MeetingPlace]]
* [[Cisco Unified MeetingPlace Release 8.0 -- Integrating Cisco Unified MeetingPlace with Cisco Unified Communications Manager#Configuring the Maximum Call Duration in Cisco Unified Communications Manager|Configuring the Maximum Call Duration in Cisco Unified Communications Manager]]
* [[Cisco Unified MeetingPlace Release 8.0 -- Integrating Cisco Unified MeetingPlace with Cisco Unified Communications Manager#Configuring the Maximum Video Call Bandwidth in Cisco Unified Communications Manager|Configuring the Maximum Video Call Bandwidth in Cisco Unified Communications Manager]]
* [[Cisco Unified MeetingPlace Release 8.0 -- Integrating Cisco Unified MeetingPlace with Cisco Unified Communications Manager#Configuring Cisco Unified Communications Manager: Music On Hold|Configuring Cisco Unified Communications Manager: Music On Hold]]
* [[Cisco Unified MeetingPlace Release 8.0 -- Integrating Cisco Unified MeetingPlace with Cisco Unified Communications Manager#Configuring How Cisco Unified MeetingPlace Displays an Endpoint as a Meeting Participant|Configuring How Cisco Unified MeetingPlace Displays an Endpoint as a Meeting Participant]]

== Configuring a SIP Trunk Security Profile in Cisco Unified Communications Manager for Cisco Unified MeetingPlace ==

We recommend that you do the following:
* Create a SIP trunk security profile in Cisco Unified Communications Manager specifically for Cisco Unified MeetingPlace.
* Apply this SIP trunk security profile to SIP trunks to Cisco Unified MeetingPlace systems.

===== Before You Begin =====
* This task applies only in Cisco Unified Communications Manager environments.
* You perform this task in the Cisco Unified Communications Manager Administration pages. Because the pages and menus vary by release, you should check the Cisco Unified Communications Manager online help for step-by-step instructions for your specific release.

===== Procedure =====

# Go to '''http://'''''ccm-server'''''/''', where ''ccm-server'' is the fully-qualified domain name or IP address of the Cisco Unified Communications Manager server.
# Sign in to Cisco Unified Communications Manager Administration.
# Select '''System > Security Profile > SIP Trunk Security Profile'''.
# Select '''Add New'''.
# Configure fields described in [[Cisco Unified MeetingPlace Release 8.0 -- Integrating Cisco Unified MeetingPlace with Cisco Unified Communications Manager#Table: Fields for SIP Trunk Security Profile Configuration|Table: Fields for SIP Trunk Security Profile Configuration]].

===== Table: Fields for SIP Trunk Security Profile Configuration =====

{| border = 1
|-
!Field
!Action
|-
|

Name
|

Enter a name, such as SIP Trunk Security Profile for Cisco Unified MeetingPlace.
|-
|

Device Security Mode
|

Select '''Non Secure'''.
|-
|

Incoming Transport Type
|

Keep the default value of '''TCP+UDP'''.

If other values are available for this field, you can instead select the value that matches the [[Cisco Unified MeetingPlace Release 8.0 -- Administration Center Page References for Cisco Unified MeetingPlace#Transport|Transport]] setting for this Cisco Unified Communications Manager node on the [[Cisco Unified MeetingPlace Release 8.0 -- Administration Center Page References for Cisco Unified MeetingPlace#SIP Configuration Page|SIP Configuration Page]].
|-
|

Outgoing Transport Type
|

We recommend that you select '''TCP'''.
|-
|

Enable Digest Authentication
|

'''Uncheck''' this check box.
|-
|

Enable Application Level Authorization
|

'''Uncheck''' this check box.
|-
|

Incoming Port
|

Make sure this value matches the [[Cisco Unified MeetingPlace Release 8.0 -- Administration Center Page References for Cisco Unified MeetingPlace#Port|Port]] setting for this Cisco Unified Communications Manager node on the [[Cisco Unified MeetingPlace Release 8.0 -- Administration Center Page References for Cisco Unified MeetingPlace#SIP Configuration Page|SIP Configuration Page]].

Default: 5060
|}

:6. Select '''Save'''.

===== Related Topics =====
* [[Cisco Unified MeetingPlace Release 8.0 -- Configuring Call Control for Cisco Unified MeetingPlace#Configuring Call Control for Cisco Unified MeetingPlace|Configuring Call Control for Cisco Unified MeetingPlace]] module
* [[Cisco Unified MeetingPlace Release 8.0 -- Configuring Reservationless Single Number Access (RSNA) for Cisco Unified MeetingPlace#Configuring Reservationless Single Number Access (RSNA) for Cisco Unified MeetingPlace|Configuring Reservationless Single Number Access (RSNA) for Cisco Unified MeetingPlace]] module
* Security Guide for your release of Cisco Unified Communications Manager at http://www.cisco.com/en/US/products/sw/voicesw/ps556/prod_maintenance_guides_list.html

== Configuring the Maximum Call Duration in Cisco Unified Communications Manager ==

The maximum length of a meeting depends on three values, the lowest of which is enforced:
* Maximum meeting length (minutes) field on the [[Cisco Unified MeetingPlace Release 8.0 -- Administration Center Page References for Cisco Unified MeetingPlace (M - P pages)#Meeting Configuration Page|Meeting Configuration Page]].
* Maximum meeting length (minutes) field in the user profile of the meeting owner.
* Maximum Call Duration Timer service parameter in Cisco Unified Communications Manager.

This task describes how to view and (if necessary) configure the service parameter in Cisco Unified Communications Manager.

===== Before You Begin =====
* This task applies only in Cisco Unified Communications Manager environments.
* You perform this task in the Cisco Unified Communications Manager Administration pages. Because the pages and menus vary by release, you should check the Cisco Unified Communications Manager online help for step-by-step instructions for your specific release.

===== Procedure =====

# Go to '''http://'''''ccm-server'''''/''', where ''ccm-server'' is the fully-qualified domain name or IP address of the Cisco Unified Communications Manager server.
# Sign in to Cisco Unified Communications Manager Administration.
# Select '''System > Service Parameters'''.
# Select the server.
# Select the Cisco CallManager service.
# Find the '''Maximum Call Duration Timer''' field in the Clusterwide Parameters (Feature - General) section.
# Modify this field only if you require meetings to last longer than the previously configured value.
#* A value of 0 disables the timer, which is recommended for continuous meetings.
#* For descriptions of this or any other field on the page, select the field name.
# Select '''Save''' if you modified any parameters.

===== Related Topics =====
* [[Cisco Unified MeetingPlace Release 8.0 -- Configuring Meetings for Cisco Unified MeetingPlace#Configuring Meetings for Cisco Unified MeetingPlace|Configuring Meetings for Cisco Unified MeetingPlace]] module
* [[Cisco Unified MeetingPlace Release 8.0 -- Configuring User Profiles and User Groups for Cisco Unified MeetingPlace#Configuring User Profiles and User Groups for Cisco Unified MeetingPlace|Configuring User Profiles and User Groups for Cisco Unified MeetingPlace]] module

== Configuring the Maximum Video Call Bandwidth in Cisco Unified Communications Manager ==

In Cisco Unified MeetingPlace, video calls cannot exceed the lowest maximum bandwidth determined by these settings:
* Maximum bit rate (kbps) field on the [[Cisco Unified MeetingPlace Release 8.0 -- Administration Center Page References for Cisco Unified MeetingPlace (A - C pages)#Add Video Type Page|Add Video Type Page]]
* Video Call Bandwidth region parameter in Cisco Unified Communications Manager.
* Bandwidth capabilities and configurations of the video endpoints.

This task describes how to view and (if necessary) modify the Video Call Bandwidth in Cisco Unified Communications Manager.

===== Before You Begin =====
* This task applies only in Cisco Unified Communications Manager environments.
* You perform this task in the Cisco Unified Communications Manager Administration pages. Because the pages and menus vary by release, you should check the Cisco Unified Communications Manager online help for step-by-step instructions for your specific release.

===== Procedure =====

# Go to '''http://'''''ccm-server'''''/''', where ''ccm-server'' is the fully-qualified domain name or IP address of the Cisco Unified Communications Manager server.
# Sign in to Cisco Unified Communications Manager Administration.
# Select '''Device > Trunk'''.
# Select '''Find''' with or without any search parameters to find the trunks that carry Cisco Unified MeetingPlace calls, for example:
#* SIP trunk to Cisco Unified MeetingPlace
#* Inter-cluster trunks between Cisco Unified Communications Manager Release 4.x or 5.x and Cisco Unified Communications Manager Release 6.1 (or later).
# Write down the name of each Device Pool that these trunks use.
# Select '''System > Device Pool'''.
# Select '''Find''' with or without any search parameters to find a device pool that carries Cisco Unified MeetingPlace calls.
# Select the Region for a device pool to go to the Region Configuration page.
# In the Region Relationships area, see the '''Video Call Bandwidth''' for each region and audio codec combination.
# (Optional) Use the Modify Relationship to other Regions area to change the Video Call Bandwidth for a particular Region and Audio Codec combination.
# Select '''Save'''.
# Repeat Step 6 to Step 11 for each device pool used by the trunks that carry Cisco Unified MeetingPlace calls.

===== Related Topics =====
* [[Cisco Unified MeetingPlace Release 8.0 -- Configuring Meetings for Cisco Unified MeetingPlace#Configuring Meetings for Cisco Unified MeetingPlace|Configuring Meetings for Cisco Unified MeetingPlace]] module

== Configuring Cisco Unified Communications Manager: Music On Hold ==

In Cisco Unified Communications Manager, you can configure music on hold so that callers hear music when one of your users places a call on hold. This can be disruptive if a user places a conference call on hold. The music, and possible announcements, can prevent other callers on the conference call from hearing each other until the user who placed the call on hold returns to the call.

You can disable music on hold for conference calls by completing these tasks:
* Creating a Media Resource Group in Cisco Unified Communications Manager for all music on hold resources.
* Adding all phones for which you want to enable music on hold to the Media Resource Group List that contains the music on hold Media Resource Group.
* Making sure that the music on hold Media Resource Group List is ''not'' assigned to the SIP trunk that connects Cisco Unified Communications Manager to Cisco Unified MeetingPlace.

===== Restrictions =====
* This procedure disables music on hold for callers within the same Cisco Unified Communications Manager cluster, but it does not disable music on hold for outside callers, including endpoints that are registered to a different Cisco Unified Communications Manager cluster than Cisco Unified MeetingPlace.
* This procedure also disables music on hold for calls between endpoints that are registered to different Cisco Unified Communications Manager servers.
: For example, suppose that your Cisco Unified MeetingPlace call-control deployment includes a Cisco Unified Communications Manager Release 6.x server and a Cisco Unified Communications Manager Release 4.x server that are connected to each other by inter-cluster trunks (ICTs). Because these ICTs will not have music on hold resources configured through the Media Resource Group List, music on hold will be disabled on all calls that pass through these ICTs.
* This procedure shows how to create a ''new'' Media Resource Group for music on hold resources. If you instead want to modify existing Media Resource Groups to complete this task, modify the steps accordingly.
* You perform this task in the Cisco Unified Communications Manager Administration pages. Because the pages and menus vary by release, you should check the Cisco Unified Communications Manager online help for step-by-step instructions for your specific release.

===== Procedure =====

# Go to '''http://'''''ccm-server'''''/ccmadmin/main.asp''', where ''ccm-server'' is the fully-qualified domain name or IP address of the Cisco Unified Communications Manager server.
# Sign in to Cisco Unified Communications Manager Administration.
# Select '''Media Resources > Media Resource Group'''.
# Select '''Add New'''.
# Configure the fields described in [[Cisco Unified MeetingPlace Release 8.0 -- Integrating Cisco Unified MeetingPlace with Cisco Unified Communications Manager#Table: Fields for Adding a Media Resource Group|Table: Fields for Adding a Media Resource Group]].

===== Table: Fields for Adding a Media Resource Group =====

{| border = 1
|-
!Field
!Action
|-
|

Name
|

Enter a name, such as MOHGroup.
|-
|

Selected Media Resources
|

Select all of the music on hold servers in the Available Media Resources list, and select the down arrow.
|}

:6. Select '''Save'''.
:7. Select '''Media Resources > Media Resource Group List'''.
:8. Select '''Add New'''.
:9. Configure the fields described in [[Cisco Unified MeetingPlace Release 8.0 -- Integrating Cisco Unified MeetingPlace with Cisco Unified Communications Manager#Table: Fields for Adding a Media Resource Group List|Table: Fields for Adding a Media Resource Group List]].

===== Table: Fields for Adding a Media Resource Group List =====

{| border = 1
|-
!Field
!Action
|-
|

Name
|

Enter a name, such as MOHList.
|-
|

Selected Media Resource Groups
|

Select the music on hold Media Resource Group (for example, MOHGroup), and select the down arrow.
|}

:10. Select '''Save'''.
:11. Configure all phones for which you want to support music on hold to use the Media Resource Group List (for example, MOHList). You can use the Bulk Administration Tool (BAT) to reconfigure many phones at one time.
:: '''Note: ''' Make sure that you do ''not'' assign a music on hold [[Cisco Unified MeetingPlace Release 8.0 -- Configuring Call Control for Cisco Unified MeetingPlace#Media Resource Group List|Media Resource Group List]] to the trunk that leads to Cisco Unified MeetingPlace.
:12. Repeat this procedure on each Cisco Unified Communications Manager to which Cisco Unified MeetingPlace-supported endpoints are registered.

===== Related Topics =====
* [[Cisco Unified MeetingPlace Release 8.0 -- Configuring Call Control for Cisco Unified MeetingPlace#Configuring Call Control for Cisco Unified MeetingPlace|Configuring Call Control for Cisco Unified MeetingPlace]] module

== Configuring How Cisco Unified MeetingPlace Displays an Endpoint as a Meeting Participant ==

'''Note: ''' This topic does not apply to systems that use the Express Media Server. Proceed only if the Type of media server field is set to '''Hardware Media Server '''on the [[Cisco Unified MeetingPlace Release 8.0 -- Administration Center Page References for Cisco Unified MeetingPlace (M - P pages)#Media Resource Configuration Page|Media Resource Configuration Page]].

Complete this task if you want to change how a phone or video endpoint appears in Cisco Unified MeetingPlace reports, video labels, and participant lists. For example, if the name of a person is displayed, then you can complete this task to have Cisco Unified MeetingPlace display the directory number (phone number) of the endpoint instead.

===== Before You Begin =====

You perform this task in the Cisco Unified Communications Manager Administration pages. Because the pages and menus vary by release, you should check the Cisco Unified Communications Manager online help for step-by-step instructions for your specific release.

===== Procedure =====

# Go to '''http://'''''cucm-server'''''/''', where ''cucm-server'' is the fully-qualified domain name or IP address of the Cisco Unified Communications Manager server.
# Sign in to Cisco Unified Communications Manager Administration.
# Select '''Device > Phone'''.
# Find the phone by searching for the '''Directory Number'''.
# Select the '''Device Name''' for the phone.
#: The device name appears as the MAC address of the phone, preceded by a few characters.
# Find the '''Association Information''' area on the left side of the screen.
# Select the '''Line''' for the relevant directory number.
# Find the following fields on the Directory Number Configuration page:
#* Directory Number
#* Display (Internal Caller ID)
#* ASCII Display (Internal Caller ID)
# Do one of the following:
#* If you want Cisco Unified MeetingPlace to always display the Directory Number of this endpoint, then delete all text in the Display (Internal Caller ID) and ASCII Display (Internal Caller ID) fields.
#* Modify the Display (Internal Caller ID) field to whatever text you want Cisco Unified MeetingPlace to display for this endpoint, for example, a name. The text you enter will automatically be copied to the ASCII Display (Internal Caller ID) field after you save your changes.
# Select '''Save'''.

===== Related Topics =====
* [[Cisco Unified MeetingPlace Release 8.0 -- Administration Center Page References for Cisco Unified MeetingPlace (M - P pages)#Table: Field Reference: Media Resource Configuration Page|Table: Field Reference: Media Resource Configuration Page]] in the [[Cisco Unified MeetingPlace Release 8.0 -- Administration Center Page References for Cisco Unified MeetingPlace (M - P pages)|Administration Center Page References for Cisco Unified MeetingPlace (M - P pages)]]

[[Category: Integrations for Cisco Unified MeetingPlace Release 8.0]]

Cisco Unified MeetingPlace Release 8.0 -- Integrating Cisco Unified MeetingPlace with Cisco Unified Communications Manager - Revision history

Annekim: /* Table: Fields for SIP Trunk Security Profile Configuration */

Annekim: /* Configuring Cisco Unified Communications Manager: Music On Hold */ added note that MoH task is not required for cucm 7.x and later

MeetingPlace Moderator: 1 revision

MeetingPlace Moderator: /* Configuring How Cisco Unified MeetingPlace Displays an Endpoint as a Meeting Participant */