Cisco Unified MeetingPlace, Release 7.0 -- Video Endpoint Compatibility
From DocWiki
Main page: Cisco Unified MeetingPlace, Release 7.0
This section provides compatibility information between Cisco Unified MeetingPlace Release 7.0 and various video terminals when using Cisco Unified Communications Manager Release 6.1(2) or higher.
All testing was performed with Cisco Unified MeetingPlace connected to Cisco Unified Communications Manager Release 6.1 or Release 7.0 via SIP trunk. For H.323 testing, the terminal was registered to a H.323 Gatekeeper, which was connected to Cisco Unified Communications Manager through an H.323 trunk. For SIP and SCCP, the terminal was registered directly to Cisco Unified Communications Manager.
Notes:
- Cisco Unified Communications Manager Release 6.1(2) or higher is required for all video installations except where only Cisco Unified Video Advantage is used, in which case Cisco Unified Communications Manager Release 6.0(3) is adequate.
- Endpoints with the following test results are likely to drop calls when transferring to a breakout session, initiating a #31 dial-out call, or exiting the meeting with #9:
- Dial in-fail
- Dial out-fail
- Direct to meeting-OK or "-"
- These video endpoints typically do not correctly support the required media transfer mechanism.
- Transferring a Cisco Unified MeetingPlace call from a Cisco-brand phone to a third-party SIP video terminal is likely to result in an audio-only connection. This is due to differences in the way Cisco and third-party terminals negotiate transport of telephony events. The differences cause Cisco Unified Communications Manager to insert a media termination point (MTP) in the call. Unless a hardware MTP resource is available, this insertion will block the video stream.
Contents |
Video Endpoint Compatibility Test Results for Release 7.0.2
Table: Video Endpoints Compatible with Cisco Unified MeetingPlace Release 7.0.2
Manufacturer/Brand | Model/Series | Protocol | Dial In | Dial Out | Direct to Meeting | 4CIF | Version Tested | Notes |
---|---|---|---|---|---|---|---|---|
Cisco |
Cisco Unified Personal Communicator |
SIP |
OK |
OK |
OK |
N |
- |
- |
Cisco |
Cisco Unified Video Advantage |
SCCP |
OK |
OK |
OK |
N |
- |
- |
Cisco |
7985 |
SCCP |
OK |
OK |
OK |
Y |
- |
- |
Cisco |
Telepresence |
SIP |
No video |
No video |
No video |
- |
- |
- |
Tandberg |
MXP Series except 150 MXP |
H.323 |
OK |
No video |
OK |
Y |
F7 |
Tested1500, 6000, 95, 3000, 1700, 990. |
Tandberg |
MXP Series except 150 MXP |
SIP |
OK |
OK |
OK |
Y |
F7 |
- |
Tandberg |
150 MXP |
H.323 |
- |
- |
- |
- |
L4.2 |
- |
Tandberg |
150 MXP |
SIP |
Fail |
OK |
OK |
- |
L4.2 |
Unable to recognize DTMF tones. |
Tandberg |
1000 |
H.323 |
OK |
No video |
OK |
- |
B 7.4, E 5.3, F7.2 |
H.263 only. |
Tandberg |
6000 |
H.323 |
OK |
No video |
OK |
Y |
E5.2, B10.3 |
H.263 only for TBG6000B. |
Polycom |
VSX Series |
H.323 |
OK |
OK |
OK |
Y |
8.5.3, 8.7.1 |
Tested 3000A, 5000, 7000 NTSC, 8000. |
Polycom |
VSX Series |
SIP |
One-way video |
One-way video |
- |
Y |
8.5.3, 8.7.1 |
- |
Polycom |
Via Video (PVX) |
H.323 |
OK |
OK |
OK |
- |
8.0.2 |
Large delay sending video by PVX. |
Polycom |
Via Video (PVX) |
SIP |
OK |
OK |
OK |
- |
8.0.2 |
- |
Polycom |
VS 512 |
H.323 |
Fail |
Fail |
- |
- |
7.5.4 |
- |
Polycom |
FX |
H.323 |
Fail |
Fail |
- |
- |
6.0.5 |
- |
Polycom |
HDX 9002 |
H.323 |
OK |
OK |
OK |
Y |
2.0.3 |
- |
Polycom |
HDX 9002 |
SIP |
OK |
OK |
OK |
Y |
2.0.3 |
Prompts are clipped. |
Aethra |
AVC 8400 |
H.323 |
OK |
OK |
OK |
Y |
6.0.30 |
Should be forced to prefer H263x4CIF in a 4CIF mode. Otherwise, it opens CIF. |
Aethra |
THESEUS |
SIP |
No video |
Fail |
- |
- |
V6.0.49 |
- |
Aethra |
Vega X5 |
H.323 |
OK |
OK |
OK |
Y |
10.2.24 |
Should be forced to prefer H263x4CIF in a 4CIF mode. Otherwise, it opens CIF. |
Aethra |
Vega X5 |
SIP |
No video |
Fail |
- |
- |
- |
- |
Aethra |
Vega X7 |
H.323 |
OK |
OK |
OK |
Y |
V12 |
Should be forced to prefer H263x4CIF in a 4CIF mode. Otherwise, it opens CIF. |
Aethra |
Vega X7 |
SIP |
OK |
Fail |
- |
- |
- |
- |
Aethra |
Vega X3 |
H.323 |
OK |
OK |
OK |
Y |
V10.7.11 |
Should be forced to prefer H263x4CIF in a 4CIF mode. Otherwise, it opens CIF. |
Aethra |
Vega X3 |
SIP |
No video |
Fail |
- |
- |
- |
- |
Sony |
PCS-1 |
H.323 |
OK |
One-way video |
- |
- |
3.31 |
- |
Sony |
PCS-1 |
SIP |
One-way video |
One-way video |
- |
- |
- |
- |
Sony |
PCS G-50 |
H.323 |
OK |
One-way video |
- |
- |
2.41 |
- |
Sony |
PCS TL-50 |
H.323 |
OK |
One-way video |
- |
- |
2.31 |
- |
Sony |
TL-30 |
H.323 |
OK |
One-way video |
- |
- |
1.24 |
- |
Sony |
XG80 |
H.323 |
Fail |
Fail |
- |
- |
2 |
No DTMF recognition. |
Sony |
XG80 |
SIP |
OK |
One-way video |
- |
- |
- |
- |
Sony |
G-70 |
H.323 |
OK |
One-way video |
- |
Y |
2.41 |
- |
France Telecom |
eConf |
H.323 |
OK |
OK |
OK |
- |
5.0.34 |
- |
France Telecom |
eConf |
SIP |
One-way video & audio |
One-way video & audio |
- |
- |
- |
RFC 2833 should be used for DTMF. |
Counterpath |
eyeBeam |
SIP |
OK |
OK |
OK |
- |
1.5 |
- |
LifeSize |
Room |
H.323 |
Fail |
Fail |
OK |
- |
LS_RM1_4.0.3(5) |
- |
Lifesize |
Room |
SIP |
Fail |
No video |
- |
Y |
- |
No DTMF recognition. |
Related Topics
- For information about Cisco Unified Video Advantage, see http://www.cisco.com/en/US/products/sw/voicesw/ps5662/tsd_products_support_series_home.html
- For information about Cisco Unified Personal Communicator, see http://www.cisco.com/en/US/products/ps6844/tsd_products_support_series_home.html
Video Endpoint Compatibility Test Results for Release 7.0.1
Table: Table 3 Video Endpoints Compatible with Cisco Unified MeetingPlace Release 7.0.1
Brand/Manufacturer | Model/Series | Protocol | Dial In | Dial Out | Direct to Meeting | Version Tested |
---|---|---|---|---|---|---|
Cisco |
Cisco Unified Personal Communicator |
SIP |
OK |
OK |
OK |
- |
Cisco |
Cisco Unified Video Advantage |
SCCP |
OK |
OK |
OK |
- |
Cisco |
7985 |
SCCP |
OK |
OK |
OK |
- |
Cisco |
Telepresence |
SIP |
no video |
no video |
no video |
- |
Tandberg |
MXP Series except MXP 150 |
H.323 |
OK |
no video |
OK |
F7.0 Beta1 |
Tandberg |
MXP Series except MXP 1500 |
H.323 |
no video |
no video |
OK |
F6.12 |
Tandberg |
MXP 1500 |
H.323 |
no video |
no video |
no video |
F6.1 |
Tandberg |
550 |
SCCP |
OK |
OK |
OK |
-3 |
Tandberg |
1000 |
SCCP |
OK |
OK |
OK |
I2.1 NTSC |
Tandberg |
1000b |
H.323 |
OK |
no video |
OK |
B 7.4 |
Tandberg |
1000E |
H.323 |
no video |
no video |
no video |
E 5.34 |
Tandberg |
6000 |
H.323 |
OK |
no video |
OK |
E5.2, B10.3 |
Polycom |
VSX Series |
H.323 |
OK |
OK |
OK |
8.5.3 |
Polycom |
VSX Series |
SIP |
fail |
fail |
- |
8.5.3 |
Polycom |
VSX Series |
SCCP |
no video |
no video |
- |
HF8.6.2a |
Polycom |
Viewstation |
H.323 |
fail |
fail |
OK |
7.2 |
Polycom |
Via Video (PVX) |
H.323 |
OK |
OK |
OK |
8.0.2 |
Polycom |
Via Video (PVX) |
SIP |
OK |
OK |
OK |
8.0.2 |
Polycom |
VS 512 |
H.323 |
fail |
fail |
- |
7.5.4 |
Polycom |
FX |
H.323 |
fail |
fail |
- |
6.0.5 |
Polycom |
HDX 9002 |
H.323 |
OK |
OK |
OK |
Beta 2.0.0 |
Polycom |
HDX 9002 |
SIP |
OK |
OK |
OK |
Beta 2.0.0 |
Aethra |
AVC 8400 |
H.323 |
OK |
OK |
OK |
6.0.30 |
Aethra |
X5 |
H.323 |
OK |
OK |
OK |
10.2.24 |
Aethra |
X7 |
H.323 |
fail |
fail |
- |
V11.1.2 |
Aethra |
Vega Star Silver |
H.323 |
OK |
OK |
OK |
6.0.30 |
Sony |
PCS-1 |
H.323 |
OK |
fail |
- |
3.31 |
Sony |
PCS G-50 |
H.323 |
OK |
fail |
- |
2.41 |
Sony |
PCS TL-50 |
H.323 |
OK |
fail |
OK |
2.31 |
Sony |
TL-30 |
H.323 |
OK |
fail |
- |
1.24 |
Sony |
HG90 |
H.323 |
fail |
fail |
- |
2.20.00 |
Sony |
G-70 |
H.323 |
OK |
fail |
- |
2.41 |
France Telecom |
eConf |
H.323 |
OK |
OK |
OK |
4.1.285 |
Counterpath |
eyeBeam |
SIP |
fail |
fail |
- |
1.5.126 |
LifeSize |
Room |
H.323 |
fail |
fail |
- |
3.0.0(23) |
LifeSize |
Room |
H.323 |
fail |
fail |
OK |
3.0.7(2) |
LifeSize |
Room |
SIP |
fail |
fail |
- |
3.0.0(23) |
Innomedia |
MTA 5531 |
SIP |
fail |
fail |
- |
-3 |
Leadtek |
BVP 8882 |
SIP |
fail |
fail |
- |
-3 |
Footnote 1: Tested MXP1700 and MXP1000 with this version; RCDO must be disabled in the terminal; low resolution video with Cisco Unified Communications Manager Release 6.1, fixed in Cisco Unified Communications Manager Release 7.0.
Footnote 2: RCDO must be disabled in the terminal; low resolution video with Cisco Unified Communications Manager Release 6.1, fixed in Cisco Unified Communications Manager Release 7.0.
Footnote 3: Not recorded.
Footnote 4: One-way video.
Footnote 5: Poor audio quality with G.722.
Footnote 6: No DTMF.
Related Topics
- For information about Cisco Unified Video Advantage, see http://www.cisco.com/en/US/products/sw/voicesw/ps5662/tsd_products_support_series_home.html
- For information about Cisco Unified Personal Communicator, see http://www.cisco.com/en/US/products/ps6844/tsd_products_support_series_home.html
Terminology Used in Video Endpoint Compatibility Test Results
The following table describes the terminology used in Table: Video Endpoints Compatible with Cisco Unified MeetingPlace Release 7.0.2 and Table: Video Endpoints Compatible with Cisco Unified MeetingPlace Release 7.0.1, which provide compatibility test results.
Terminology | Description |
---|---|
Test | |
Dial In |
Tested dialing in to Cisco Unified MeetingPlace. |
Dial Out |
Tested dialing out from Cisco Unified MeetingPlace by using a web browser command or by using the TUI command #31. |
Direct to Meeting |
Tested dialing out from Cisco Unified MeetingPlace using the scheduled "direct to meeting" mode. The process was to configure a video terminal profile for outdial to terminal, tell the video terminal to skip the meeting entry prompts on outdial, and then invite the terminal to the meeting. |
4CIF |
Tested whether the terminal worked when tested with 4CIF using H.263. |
Result | |
OK |
The terminal was able to enter a meeting using video. |
No video |
The terminal was able to enter a meeting, but without video or (in Release 7.0.1 results only) with one-way video. |
Fail |
The terminal was not able to enter a meeting. The failure may have been at initial connection or at meeting entry. |
"-" |
The terminal was not tested in this mode. |
Video Format Support
Table: Supported Video Formats lists the supported video formats for various combinations of the global video mode and the codec used by the video terminal.
Notes:
- If Cisco Unified Communications Manager causes the connection rate to be lower than the maximum for your global video mode setting (384 kbps for standard rate, 2 Mbps for high rate), then the resolution or frames per second sent by Cisco Unified MeetingPlace may be reduced.
- For a Release 7.0.2 system:
- H.263 and H.261 are offered only by defining a video terminal profile.
- Otherwise, only H.264 will be offered.
- For a Release 7.0.1 system:
- 4CIF is not supported.
- All three codecs can be negotiated in high rate without a video terminal profile.
- H.263 and H.264 can be negotiated in standard rate without a video terminal profile.
Table: Supported Video Formats
Global Video Mode | Codec | Video Format | Frames per Second |
---|---|---|---|
High rate (2 Mbps maximum) |
H.264 |
CIF, QCIF |
30 |
H.263 |
4CIF |
15 | |
H.263 |
CIF, QCIF |
30 | |
H.261 |
CIF, QCIF |
30 | |
Standard rate (384 kbps maximum) |
H.264 |
CIF |
15 |
H.264 |
QCIF |
30 | |
H.263 |
CIF, QCIF |
30 |