Cisco Unified MeetingPlace, Release 6.x -- Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway Software Release 5.3 for Use With Release 6.x - Revision history

Cgriffen: /* About Reservationless Single Number Access Configuration */

2011-08-27T16:26:25Z

About Reservationless Single Number Access Configuration

← Older revision		Revision as of 16:26, 27 August 2011
Line 718:		Line 718:


		+	=== Configuring Cisco Unified MeetingPlace 6.0 IP Gateway for SIP ===
		+
		+	You must configure Cisco Unified Communications Manager (CUCM) to operate with Cisco Unified MeetingPlace IP Gateway 6.x.
		+
		+
		+	==== Configuring a SIP Trunk Profile ====
		+
		+	Configure your SIP trunk profile to select the correct communications protocol to work with IP gateway.
		+
		+	# Go to '''http''':''//ccm-server/'', where ''ccm-server'' is the fully-qualified domain name or IP address of the Cisco Unified Communications Manager server.
		+	# Sign in to Cisco Unified Communications Manager Administration.
		+	# Select '''System > Security Profile > SIP Trunk Security Profile'''.
		+	# Create a new SIP trunk security profile with the following settings:
		+	#* Device Security mode: '''Non-secure'''
		+	#* Incoming Transport Type: '''TCP + UDP'''
		+	#* Outgoing Transport Type: '''UDP'''
		+	#* Incoming port: '''5060'''
		+	#* Select '''Accept Presence Subscription'''
		+	#* Select '''Accept Out-of-Dialog REFER'''
		+	#* Select '''Accept Unsolicited Notification'''
		+	#* Select '''Accept Replaces Header'''
		+	# Select '''Save'''.
		+
		+
		+	==== Configuring a SIP Profile ====
		+
		+	Configure a SIP profile to set up your SIP device parameters.
		+
		+	# Go to '''http''':''//ccm-server/'', where ''ccm-server'' is the fully-qualified domain name or IP address of the Cisco Unified Communications Manager server.
		+	# Sign in to Cisco Unified Communications Manager Administration.
		+	# Select '''Device > Device Settings > SIP Profile'''.
		+	# Create a new SIP profile with the following settings:
		+	#* Default MTP Telephony Eevent Payload Type: '''101'''
		+	#* Select '''Conference Join Enabled'''
		+	#* Select '''Semi Attended Transfer'''
		+	#* Leave all other settings as default
		+	# Select '''Save'''.
		+
		+
		+	==== Configuring a SIP Trunk ====
		+
		+	Configuring a SIP trunk to establish a connection to the Cisco Unified MeetingPlace IP Gateway.
		+
		+	# Go to '''http''':''//ccm-server/'', where ''ccm-server'' is the fully-qualified domain name or IP address of the Cisco Unified Communications Manager server.
		+	# Sign in to Cisco Unified Communications Manager Administration.
		+	# Select '''Device > Trunk'''.
		+	# Enter the trunk name.
		+	# Configure the following settings:
		+	#* Inbound Calls: '''Significant Digits''' (user configurable)
		+	#* SIP Information
		+	#** Destination Address: Enter the IP gateway IP address.
		+	#** Destination Port: '''5060''' (matches with IPGW SIP configuration later).
		+	#** SIP Trunk Security Profile: Use the security profile that you created in the procedure above.
		+	#** SIP Profile: Use the profile that you created in the procedure above.
		+	#** DTMF Signalling Method: '''RFC 2833'''
		+	# Select '''Save'''.
		+
		+
		+	==== Configuring a SIP Route Pattern ====
		+
		+	Configure one SIP route pattern for each remote IP gateway to send the call to Cisco Unified MeetingPlace using a SIP trunk.
		+
		+	# Go to '''http''':''//ccm-server/'', where ''ccm-server'' is the fully-qualified domain name or IP address of the Cisco Unified Communications Manager server.
		+	# Sign in to Cisco Unified Communications Manager Administration.
		+	# Select '''Call Routing > SIP Route Pattern'''.
		+	# Create a new SIP route pattern, and select an IPv4 address (MeetingPlace IP GWY).
		+	# Configure the SIP route pattern to use the SIP trunk that you created in the procedure above.
		+	# Select '''Save'''.
		+
		+
		+	==== Configuring a Route Pattern ====
		+
		+	Configure a route pattern to send the call to Cisco Unified MeetingPlace using a SIP Trunk.
		+
		+	# Go to '''http''':''//ccm-server/'', where ''ccm-server'' is the fully-qualified domain name or IP address of the Cisco Unified Communications Manager server.
		+	# Sign in to Cisco Unified Communications Manager Administration.
		+	# Select '''Call Routing > Route/Hunt > Route Pattern'''.
		+	#: '''Note: ''' You can optionally select '''Route Group > Route List''' first.
		+	# Create a new route pattern, using the domain name that you plan to use to call Cisco Unified MeetingPlace. Configure the following settings:
		+	#* Gateway/Route List: Select the SIP trunk that you created in the procedure above.
		+	#* Route Option: '''Route This Pattern'''.
		+	#** Call Classification: '''OnNet'''.
		+	#** Deselect '''Provide Outside Dial Tone'''.
		+	# Select '''Save'''.
		+
		+
		+	=== Configuring Cisco Unified MeetingPlace IP Gateway ===
		+
		+	# Sign in to the MeetingPlace IP Gateway server (Windows log on as the server’s administrator).
		+	# Double-click the orange door in the System Tray.
		+	#* Select '''IP Gateway Common''' and set Outdial Protocol to '''maximum number of callers'''. Select '''IP Gateway SIP''' and configure the following settings:
		+	#** Enabled: '''Yes'''
		+	#** User Name: Enter the domain name you configured for the Route Pattern in CUCM.
		+	#** Enter a Session Name.
		+	#** Proxy Settings and Proxy Server Address: Select '''Add''' and enter the CUCM IP address
		+	# Select '''Save'''.
		+	# Enter '''5060 '''for the Proxy Server Port.
		+	# Select '''Apply'''.
		+	# Select '''Save'''.
		+	# Select '''Control Panel > Services'''.
		+	# Select '''Cisco MeetingPlace IP Gateway '''and then select '''Restart''' after all the call processing is correct (calling search space, partition, device pool, and device codec).

	== Allowing Reverse Connections to the MeetingPlace Audio Server ==		== Allowing Reverse Connections to the MeetingPlace Audio Server ==

Dunn: /* Suppressing Music-On-Hold */ additional note to mention CSCtg45036

2010-10-30T23:39:47Z

Suppressing Music-On-Hold: additional note to mention CSCtg45036

← Older revision		Revision as of 23:39, 30 October 2010
Line 733:		Line 733:
	Specifically, make sure you do not assign to the Cisco Unified MeetingPlace H.323/SIP IP Gateway a Media Resource Group List that includes any Media Resource Group that includes Music on Hold servers, as the MeetingPlace IP Gateway can join a multicast Music-On-Hold (MoH) group. Since MeetingPlace is a transmit/receive environment, being put on hold can mean meeting participants listen to MoH, as well meetings in progress to devices configured to participate in the multicast group, resulting unexpected and undesirable privacy breaches.		Specifically, make sure you do not assign to the Cisco Unified MeetingPlace H.323/SIP IP Gateway a Media Resource Group List that includes any Media Resource Group that includes Music on Hold servers, as the MeetingPlace IP Gateway can join a multicast Music-On-Hold (MoH) group. Since MeetingPlace is a transmit/receive environment, being put on hold can mean meeting participants listen to MoH, as well meetings in progress to devices configured to participate in the multicast group, resulting unexpected and undesirable privacy breaches.

-	As an additional workaround/resolution, if the customer is using Cisco Unified Communications Manager (CUCM) Version 6.0 and later, verify the CUCM Service Parameter "Send Multicast MOH in H.245 OLC Message" is set to ~~True~~.	+	As an additional workaround/resolution, if the customer is using Cisco Unified Communications Manager (CUCM) Version 6.1 and later, verify the CUCM Service Parameter "Send Multicast MOH in H.245 OLC Message" is set to False.

	For information on configuring Media Resource Groups and Media Resource Group Lists, and associating these lists with endpoints, see the documentation for your release of Cisco Unified Communications Manager.		For information on configuring Media Resource Groups and Media Resource Group Lists, and associating these lists with endpoints, see the documentation for your release of Cisco Unified Communications Manager.

-	'''Note: ''' This solution does not suppress music on hold for remote endpoints which are registered to a different Cisco Unified Communications Manager cluster than Cisco Unified MeetingPlace.	+	'''Note: ''' This solution does not suppress music on hold for remote endpoints which are registered to a different Cisco Unified Communications Manager cluster than Cisco Unified MeetingPlace. If the CUCM cluster connecting to MeetingPlace is v7.1.2 please also note of defect CSCtg45036.

Dunn: /* Suppressing Music-On-Hold */ adding information about caveat when having MRGL that can join multicast group. Refer to TAC SR 614208939

2010-10-29T12:21:06Z

Suppressing Music-On-Hold: adding information about caveat when having MRGL that can join multicast group. Refer to TAC SR 614208939

← Older revision		Revision as of 12:21, 29 October 2010
Line 731:		Line 731:
	You can configure Cisco Unified Communications Manager to play music for the held party when users put a call on hold. However, if a user places a meeting on hold, the music plays into the meeting until the user retrieves the held call. To prevent this, you can configure Cisco Unified Communications Manager not to play music on hold for calls routed through Cisco Unified MeetingPlace H.323/SIP IP Gateway.		You can configure Cisco Unified Communications Manager to play music for the held party when users put a call on hold. However, if a user places a meeting on hold, the music plays into the meeting until the user retrieves the held call. To prevent this, you can configure Cisco Unified Communications Manager not to play music on hold for calls routed through Cisco Unified MeetingPlace H.323/SIP IP Gateway.

-	Specifically, make sure you do not assign to the Cisco Unified MeetingPlace H.323/SIP IP Gateway a Media Resource Group List that includes any Media Resource Group that includes Music on Hold servers. ~~For information~~ on ~~configuring Media Resource Groups and Media Resource Group Lists~~, ~~and associating these lists with endpoints, see~~ the ~~documentation for your release of Cisco Unified Communications Manager~~.	+	Specifically, make sure you do not assign to the Cisco Unified MeetingPlace H.323/SIP IP Gateway a Media Resource Group List that includes any Media Resource Group that includes Music on Hold servers, as the MeetingPlace IP Gateway can join a multicast Music-On-Hold (MoH) group. Since MeetingPlace is a transmit/receive environment, being put on hold can mean meeting participants listen to MoH, as well meetings in progress to devices configured to participate in the multicast group, resulting unexpected and undesirable privacy breaches.

		+	As an additional workaround/resolution, if the customer is using Cisco Unified Communications Manager (CUCM) Version 6.0 and later, verify the CUCM Service Parameter "Send Multicast MOH in H.245 OLC Message" is set to True.
		+
		+	For information on configuring Media Resource Groups and Media Resource Group Lists, and associating these lists with endpoints, see the documentation for your release of Cisco Unified Communications Manager.

	'''Note: ''' This solution does not suppress music on hold for remote endpoints which are registered to a different Cisco Unified Communications Manager cluster than Cisco Unified MeetingPlace.		'''Note: ''' This solution does not suppress music on hold for remote endpoints which are registered to a different Cisco Unified Communications Manager cluster than Cisco Unified MeetingPlace.

Anmarti2: /* Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With an H.323 Gatekeeper */

2010-02-16T15:43:48Z

Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With an H.323 Gatekeeper

← Older revision		Revision as of 15:43, 16 February 2010
Line 531:		Line 531:
	## Click on Add, and then OK		## Click on Add, and then OK
	#: '''Tip: ''' You can also access Cisco Unified MeetingPlace H.323/SIP IP Gateway configuration settings through the Registry Editor by navigating to \\HKEY_LOCAL_MACHINE\SOFTWARE\Latitude\MeetingPlace IP Gateway.		#: '''Tip: ''' You can also access Cisco Unified MeetingPlace H.323/SIP IP Gateway configuration settings through the Registry Editor by navigating to \\HKEY_LOCAL_MACHINE\SOFTWARE\Latitude\MeetingPlace IP Gateway.
-	# Use the settings in [[Cisco Unified MeetingPlace, Release 6.x -- Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway Software Release 5.3 for Use With Release 6.x#Table: Cisco Unified MeetingPlace H.323/SIP IP Gateway software Release 5.3 Configuration Settings for Use With an H.323 Gatekeeper\|Table: Cisco Unified MeetingPlace H.323/SIP IP Gateway software Release 5.3 Configuration Settings for Use With an H.323 Gatekeeper]] to configure Cisco Unified MeetingPlace H.323/SIP IP Gateway for use with an H.323 gatekeeper.	+	# Use the settings in [[Cisco Unified MeetingPlace, Release 6.x -- Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway Software Release 5.3 for Use With Release 6.x#Table: Cisco Unified MeetingPlace H.323/SIP IP Gateway software Release 5.3 and Release 6.0 Configuration Settings for Use With an H.323 Gatekeeper\|Table: Cisco Unified MeetingPlace H.323/SIP IP Gateway software Release 5.3 Configuration Settings for Use With an H.323 Gatekeeper]] to configure Cisco Unified MeetingPlace H.323/SIP IP Gateway for use with an H.323 gatekeeper.

	===== Table: Cisco Unified MeetingPlace H.323/SIP IP Gateway Software Release 5.3 and Release 6.0 Configuration Settings for Use With an H.323 Gatekeeper=====		===== Table: Cisco Unified MeetingPlace H.323/SIP IP Gateway Software Release 5.3 and Release 6.0 Configuration Settings for Use With an H.323 Gatekeeper=====

Anmarti2: /* Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With Cisco SIP Proxy Server */

2010-02-16T15:40:58Z

Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With Cisco SIP Proxy Server

← Older revision		Revision as of 15:40, 16 February 2010
Line 433:		Line 433:
	# Use the settings in the following table to configure Cisco Unified MeetingPlace H.323/SIP IP Gateway for use with Cisco SIP Proxy Server: .		# Use the settings in the following table to configure Cisco Unified MeetingPlace H.323/SIP IP Gateway for use with Cisco SIP Proxy Server: .

-	===== Table: Cisco Unified MeetingPlace H.323/SIP IP Gateway Software Release 5.~~3and~~ Release 6.0 Configuration Settings for Use With Cisco SIP Proxy Server=====	+	===== Table: Cisco Unified MeetingPlace H.323/SIP IP Gateway Software Release 5.3 and Release 6.0 Configuration Settings for Use With Cisco SIP Proxy Server=====

	{\| border = 1		{\| border = 1

Anmarti2: /* Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With an H.323 Gatekeeper */

2010-02-16T15:40:10Z

Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With an H.323 Gatekeeper

← Older revision		Revision as of 15:40, 16 February 2010
Line 522:		Line 522:


-	# ~~From~~ the ~~IP-gateway~~ server~~, choose '''Start~~''' '''> Programs > MeetingPlace Applications > MeetingPlace ~~Management'''.~~	+	# Access the server(s) Cisco Unified MeetingPlace H.323/SIP IP Gateway is installed on
-	# ~~Double-click the~~ Cisco Unified MeetingPlace ~~IP Gateway icon~~.	+	# '''For Cisco Unified MeetingPlace Release 6.0 MR3 and above'''
-	#:	+	## Double-click the orange door icon in the system tray or go to Start > Programs > MeetingPlace Applications > MeetingPlace Gateway Configuration
-	#~~: The Cisco Unified~~ MeetingPlace IP Gateway Management Console ~~opens.~~	+	#; For Cisco Unified MeetingPlace Release 6.0 MR2 and below
-	#:	+	## Go to Start, Run, and type "mmc"
		+	## Go to File, Add/Remove Snap-in
		+	## In the Standalone Snap-ins window select MeetingPlace IP Gateway & MeetingPlace Management Console
		+	## Click on Add, and then OK
	#: '''Tip: ''' You can also access Cisco Unified MeetingPlace H.323/SIP IP Gateway configuration settings through the Registry Editor by navigating to \\HKEY_LOCAL_MACHINE\SOFTWARE\Latitude\MeetingPlace IP Gateway.		#: '''Tip: ''' You can also access Cisco Unified MeetingPlace H.323/SIP IP Gateway configuration settings through the Registry Editor by navigating to \\HKEY_LOCAL_MACHINE\SOFTWARE\Latitude\MeetingPlace IP Gateway.
-	#:
-	#: '''Note:''' Starting with Cisco Unified MeetingPlace Release 6.0 MR3, the Cisco Unified MeetingPlace H.323/SIP IP Gateway no longer uses the Management Console. Instead, to configure the gateway, use the Cisco Unified MeetingPlace Gateway Configuration utility. Access the utility by right-clicking the orange door icon in the system tray.
	# Use the settings in [[Cisco Unified MeetingPlace, Release 6.x -- Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway Software Release 5.3 for Use With Release 6.x#Table: Cisco Unified MeetingPlace H.323/SIP IP Gateway software Release 5.3 Configuration Settings for Use With an H.323 Gatekeeper\|Table: Cisco Unified MeetingPlace H.323/SIP IP Gateway software Release 5.3 Configuration Settings for Use With an H.323 Gatekeeper]] to configure Cisco Unified MeetingPlace H.323/SIP IP Gateway for use with an H.323 gatekeeper.		# Use the settings in [[Cisco Unified MeetingPlace, Release 6.x -- Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway Software Release 5.3 for Use With Release 6.x#Table: Cisco Unified MeetingPlace H.323/SIP IP Gateway software Release 5.3 Configuration Settings for Use With an H.323 Gatekeeper\|Table: Cisco Unified MeetingPlace H.323/SIP IP Gateway software Release 5.3 Configuration Settings for Use With an H.323 Gatekeeper]] to configure Cisco Unified MeetingPlace H.323/SIP IP Gateway for use with an H.323 gatekeeper.

Line 623:		Line 624:
	4. To accept the settings, click '''Submit'''.		4. To accept the settings, click '''Submit'''.

-	5. Restart the IP-gateway server.	+	5. Restart the IP-gateway server.
-		+

	=== Verifying MeetingPlace H.323/SIP IP Gateway Configuration ===		=== Verifying MeetingPlace H.323/SIP IP Gateway Configuration ===

Anmarti2: /* Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With Cisco SIP Proxy Server */

2010-02-16T15:39:49Z

Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With Cisco SIP Proxy Server

← Older revision		Revision as of 15:39, 16 February 2010
Line 422:		Line 422:


-	# ~~From~~ the ~~IP-gateway~~ server~~, choose '''Start~~''' '''> Programs > MeetingPlace Applications > MeetingPlace ~~Management'''.~~	+	# Access the server(s) Cisco Unified MeetingPlace H.323/SIP IP Gateway is installed on
-	# ~~Double-click the~~ Cisco Unified MeetingPlace ~~IP Gateway icon~~.	+	# '''For Cisco Unified MeetingPlace Release 6.0 MR3 and above'''
-	#:	+	## Double-click the orange door icon in the system tray or go to Start > Programs > MeetingPlace Applications > MeetingPlace Gateway Configuration
-	#~~: The Cisco Unified~~ MeetingPlace IP Gateway Management Console ~~opens.~~	+	#; For Cisco Unified MeetingPlace Release 6.0 MR2 and below
-	#:	+	## Go to Start, Run, and type "mmc"
-	#: '''Tip: ''' You can also access Cisco Unified MeetingPlace H.323/SIP IP Gateway configuration settings through the Registry Editor by navigating to \\HKEY_LOCAL_MACHINE\SOFTWARE\Latitude\MeetingPlace IP Gateway.	+	## Go to File, Add/Remove Snap-in
-	#:	+	## In the Standalone Snap-ins window select MeetingPlace IP Gateway & MeetingPlace Management Console
-	#: '''Note:''' Starting with Cisco Unified MeetingPlace Release 6.0 MR3, the Cisco Unified MeetingPlace H.323/SIP IP Gateway no longer uses the Management Console. Instead, to configure the gateway, use the Cisco Unified MeetingPlace Gateway Configuration utility. Access the utility by right-clicking the orange door icon in the system tray.	+	## Click on Add, and then OK
-	#:	+	#: '''Tip: ''' You can also access Cisco Unified MeetingPlace H.323/SIP IP Gateway configuration settings through the Registry Editor by navigating to \\HKEY_LOCAL_MACHINE\SOFTWARE\Latitude\MeetingPlace IP Gateway.
	# Use the settings in the following table to configure Cisco Unified MeetingPlace H.323/SIP IP Gateway for use with Cisco SIP Proxy Server: .		# Use the settings in the following table to configure Cisco Unified MeetingPlace H.323/SIP IP Gateway for use with Cisco SIP Proxy Server: .

Line 514:		Line 514:
	4. To accept the settings, click '''Submit'''.		4. To accept the settings, click '''Submit'''.

-	5. Restart the IP-gateway server.	+	5. Restart the IP-gateway server.
-		+

	=== Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With an H.323 Gatekeeper ===		=== Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With an H.323 Gatekeeper ===

Anmarti2: /* Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With Cisco Unified Communications Manager */

2010-02-16T15:39:32Z

Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With Cisco Unified Communications Manager

← Older revision		Revision as of 15:39, 16 February 2010
Line 321:		Line 321:


-	# ~~From~~ the ~~IP-gateway~~ server~~, choose '''Start~~''' '''> Programs > MeetingPlace Applications > MeetingPlace ~~Management'''.~~	+	# Access the server(s) Cisco Unified MeetingPlace H.323/SIP IP Gateway is installed on
-	# ~~Double-click the~~ Cisco Unified MeetingPlace ~~IP Gateway icon~~.	+	# '''For Cisco Unified MeetingPlace Release 6.0 MR3 and above'''
-	#:	+	## Double-click the orange door icon in the system tray or go to Start > Programs > MeetingPlace Applications > MeetingPlace Gateway Configuration
-	#~~: The Cisco Unified~~ MeetingPlace IP Gateway Management Console ~~opens.~~	+	#; For Cisco Unified MeetingPlace Release 6.0 MR2 and below
-	#:	+	## Go to Start, Run, and type "mmc"
		+	## Go to File, Add/Remove Snap-in
		+	## In the Standalone Snap-ins window select MeetingPlace IP Gateway & MeetingPlace Management Console
		+	## Click on Add, and then OK
	#: '''Tip: ''' You can also access Cisco Unified MeetingPlace H.323/SIP IP Gateway configuration settings through the Registry Editor by navigating to \\HKEY_LOCAL_MACHINE\SOFTWARE\Latitude\MeetingPlace IP Gateway.		#: '''Tip: ''' You can also access Cisco Unified MeetingPlace H.323/SIP IP Gateway configuration settings through the Registry Editor by navigating to \\HKEY_LOCAL_MACHINE\SOFTWARE\Latitude\MeetingPlace IP Gateway.
-	#:
-	#: '''Note:''' Starting with Cisco Unified MeetingPlace Release 6.0 MR3, the Cisco Unified MeetingPlace H.323/SIP IP Gateway no longer uses the Management Console. Instead, to configure the gateway, use the Cisco Unified MeetingPlace Gateway Configuration utility. Access the utility by right-clicking the orange door icon in the system tray.
-	#:
	# Use the settings in [[Cisco Unified MeetingPlace, Release 6.x -- Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway Software Release 5.3 for Use With Release 6.x#Table: Configuration Settings for Use with Cisco Unified Communications Manager\|Table: Configuration Settings for Use with Cisco Unified Communications Manager]] to configure Cisco Unified MeetingPlace H.323/SIP IP Gateway for use with Cisco Unified Communications Manager:		# Use the settings in [[Cisco Unified MeetingPlace, Release 6.x -- Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway Software Release 5.3 for Use With Release 6.x#Table: Configuration Settings for Use with Cisco Unified Communications Manager\|Table: Configuration Settings for Use with Cisco Unified Communications Manager]] to configure Cisco Unified MeetingPlace H.323/SIP IP Gateway for use with Cisco Unified Communications Manager:

Line 414:		Line 414:
	4. To accept the settings, click '''Submit'''.		4. To accept the settings, click '''Submit'''.

-	5. Restart the IP-gateway server.	+	5. Restart the IP-gateway server.
-		+

	=== Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With Cisco SIP Proxy Server ===		=== Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With Cisco SIP Proxy Server ===

Anmarti2: /* About Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway */

2010-02-16T15:18:15Z

About Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway

← Older revision		Revision as of 15:18, 16 February 2010
Line 35:		Line 35:


-	'''Note:''' Starting with Cisco Unified MeetingPlace Release 6.0 Maintenance Release 3 (MR3), the Cisco Unified MeetingPlace H.323/SIP IP Gateway no longer uses the Management Console. Instead, to configure the gateway, use the Cisco Unified MeetingPlace Gateway Configuration utility. Access the utility by ~~right~~-clicking the orange door icon in the system tray.	+	'''Note:''' Starting with Cisco Unified MeetingPlace Release 6.0 Maintenance Release 3 (MR3), the Cisco Unified MeetingPlace H.323/SIP IP Gateway no longer uses the Management Console. Instead, to configure the gateway, use the Cisco Unified MeetingPlace Gateway Configuration utility. Access the utility by double-clicking the orange door icon in the system tray.


Line 300:		Line 300:

	\|}		\|}
-
-
-
-

	== How to Configure Cisco Unified MeetingPlace H.323/SIP IP Gateway ==		== How to Configure Cisco Unified MeetingPlace H.323/SIP IP Gateway ==

Jmcmulle: CSCsj54232, added note about configuring 2 IP addresses for CUCM

2009-08-10T20:55:25Z

CSCsj54232, added note about configuring 2 IP addresses for CUCM

← Older revision		Revision as of 20:55, 10 August 2009
Line 319:		Line 319:

	=== Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With Cisco Unified Communications Manager ===		=== Configuring Cisco Unified MeetingPlace H.323/SIP IP Gateway for Use With Cisco Unified Communications Manager ===
		+
		+
		+	'''Note:''' If you are configuring the Cisco Unified MeetingPlace H.323/SIP IP Gateway for use with Cisco Unified Communications Manager on a system that also hosts the Cisco Unified MeetingPlace Web Server, you need to configure a separate gateway in Cisco Unified Communications Manager for each of the two IP addresses that the Cisco Unified MeetingPlace Web Server uses.
		+