Cchetty: 1 revision

2010-04-09T15:20:55Z

1 revision

← Older revision

Revision as of 15:20, 9 April 2010

Isdas: /* Cisco Unified CCX Engine is running but calls are not answered */

2010-01-21T09:02:35Z

Cisco Unified CCX Engine is running but calls are not answered

← Older revision		Revision as of 09:02, 21 January 2010
Line 1:		Line 1:
-	~~{{Template:Required Metadata}}~~
	== Cisco Unified CCX Engine is running but calls are not answered ==		== Cisco Unified CCX Engine is running but calls are not answered ==

Line 33:		Line 32:

	[[Category:Unified CCX, Release 7.0]]		[[Category:Unified CCX, Release 7.0]]
		+	[[Category:Unified CCX, Release 8.0]]

Docwikibot: Bot: Adding {{Template:Required Metadata}}

2009-12-18T18:21:39Z

Bot: Adding {{Template:Required Metadata}}

← Older revision		Revision as of 18:21, 18 December 2009
Line 1:		Line 1:
		+	{{Template:Required Metadata}}
	== Cisco Unified CCX Engine is running but calls are not answered ==		== Cisco Unified CCX Engine is running but calls are not answered ==

Cchetty: 1 revision

2009-08-12T19:50:37Z

1 revision

← Older revision

Revision as of 19:50, 12 August 2009

Sansahoo: /* Cisco Unified CCX Engine is running but calls are not answered */

2009-07-28T11:04:49Z

Cisco Unified CCX Engine is running but calls are not answered

New page

== Cisco Unified CCX Engine is running but calls are not answered ==

{| border="1"
|-
! '''Problem Summary'''
| The Cisco Unified CCX Engine is running but the Cisco Unified CCX system does not answer calls.
|-
! '''Error Message'''
| None.
|-
! '''Possible Cause'''
| The JTAPI subsystem is out of service, the trigger is disabled, the application is disabled, the maximum number of sessions or maximum number of tasks were exceeded, or no CTI ports or media channels are available for the trigger.
|-
! '''Recommended Action'''
|
Complete the following steps:

# From the Cisco Unified CCX Administration web page, choose System > Control Center, pick up the servers on the left panel, and expand the Cisco Unified CCX Engine to verify that the JTAPI subsystem is in service. If the JTAPI subsystem is in partial service, see the “JTAPI subsystem is in partial service” troubleshooting tip in this guide. If the JTAPI subsystem out of service, refer to the “Cisco Unified CCX Provisioning for Cisco Unified Communications Manager” section in the ''Cisco Unified Contact Center Express Administration Guide'' for information about configuration.
# From the Cisco Unified CCX Administration web page, choose '''Subsystems > JTAPI''' and click the '''JTAPI Triggers'' hyperlink. If False appears in the Enabled column for the trigger, double-click the trigger, click the Enabled Yes radio button, and then click Update.
# From the Cisco Unified CCX Administration web page, choose '''Applications > Configure Applications'''. If '''No''' appears in the '''Enabled''' column for the application, double-click the application, click the '''Enabled Yes''' radio button, and then click '''Update'''.
# In the Cisco Unified CCX trace files, verify that the calls do not exceed the maximum number of allowed sessions.
# In the Cisco Unified CCX trace files, verify that the calls do not exceed the maximum number of allowed tasks.
# In the Cisco Unified CCX trace files, make sure that there are no messages regarding insufficient free CTI ports or media channels.
|-
! '''Release'''
| Release 7.0(1)
|-
! '''Associated CDETS #'''
| None.
|-
|}

[[Category:Unified CCX, Release 7.0]]

Cisco Unified CCX Engine is running but calls are not answered - Revision history

Cchetty: 1 revision

Isdas: /* Cisco Unified CCX Engine is running but calls are not answered */

Docwikibot: Bot: Adding {{Template:Required Metadata}}

Cchetty: 1 revision

Sansahoo: /* Cisco Unified CCX Engine is running but calls are not answered */