Cisco Plug and Play Application -- Troubleshooting

From DocWiki

(Difference between revisions)
Jump to: navigation, search
Line 15: Line 15:
=== Supported Platform  ===
=== Supported Platform  ===
-
iPad or iPhone running iOS version 5.0 or later<br>
+
iPad or iPhone running iOS version 5.0 or later  
== Windows Application  ==
== Windows Application  ==
Line 30: Line 30:
=== Troubleshooting<br>  ===
=== Troubleshooting<br>  ===
-
===== Another instance of the Cisco Plug and Play Application is running. Terminate the previous instance before launching the application<br>  =====
+
===== Another instance of the Cisco Plug and Play Application is running. Terminate the previous instance before launching the application =====
-
'''Message Type:'''<br>
+
'''Message Type:'''
Error message<br>  
Error message<br>  
Line 38: Line 38:
'''Symptom:'''<br>  
'''Symptom:'''<br>  
-
A popup error message "Another instance of Cisco Plug and Play Application is running. Terminate the previous instance before launching" is displayed.<br>
+
A popup error message "Another instance of Cisco Plug and Play Application is running. Terminate the previous instance before launching" is displayed.
'''Solution:'''  
'''Solution:'''  
Line 44: Line 44:
Make sure that the Cisco Plug and Play Application is not already running. If it is running, you must either close the application before launching the application again or continue to use the already running instance of the application.  
Make sure that the Cisco Plug and Play Application is not already running. If it is running, you must either close the application before launching the application again or continue to use the already running instance of the application.  
-
==== A device is being deployed. Terminating the deployment process might affect the device configuration. Do you want to terminate?<br> ====
+
==== A device is being deployed. Terminating the deployment process might affect the device configuration. Do you want to terminate?  ====
'''Message Type:'''<br>  
'''Message Type:'''<br>  

Revision as of 08:03, 18 April 2013

Cisco Plug and Play Application -- Troubleshooting

Contents

Introduction

The Cisco Plug and Play Application simplifies branch network rollout by securely and automatically delivering the bootstrap configuration on the Cisco Integrated Services Router (ISR) and Cisco ISR-G2 during deployment.

The Cisco Plug and Play Application downloads the bootstrap configuration from the Cisco Prime Infrastructure and deploys it. The Cisco Plug and Play Application connects to the Cisco Plug and Play Gateway to communicate with Cisco Prime Infrastructure for downloading the bootstrap configuration.

The Cisco Plug and Play Application automates and monitors the deployment progress, starting from delivering the bootstrap configuration, and until the entire deployment operation is complete. It thereby reduces the total deployment time and costs involved in this operation.

This document captures the troubleshooting information for both the iOS and Windows applications.

iOS Application

Supported Platform

iPad or iPhone running iOS version 5.0 or later

Windows Application

Supported Operating System

  • Windows XP
  • Windows 2000
  • Windows Vista
  • Windows 7

Note: Windows 8 is currently not supported.

Troubleshooting

Another instance of the Cisco Plug and Play Application is running. Terminate the previous instance before launching the application

Message Type:

Error message

Symptom:

A popup error message "Another instance of Cisco Plug and Play Application is running. Terminate the previous instance before launching" is displayed.

Solution:

Make sure that the Cisco Plug and Play Application is not already running. If it is running, you must either close the application before launching the application again or continue to use the already running instance of the application.

A device is being deployed. Terminating the deployment process might affect the device configuration. Do you want to terminate?

Message Type:

Confirmation/Alert message.

Symptom:

This error is seen when you try to close the application, while deployment is still in progress.

Solution:
Wait until the deployment is completed or close the application by clicking Yes. Clicking Yes will terminate the deployment. If you click No, the deployment operation will continue.

Unable to load the help document

Message type:

Symptom:
This error message is seen when you try to launch the user guide or troubleshooting guide from the application.

Solution:
Make sure that you have Adobe PDF reader installed on your laptop.

Bootstrap configuration download failed

Message Type:
Error message

Symptom:
Bootstrap configuration download failed

Solution:

  • Verify the status of the Cisco Prime Infrastructure server and the Cisco Plug and Play Gateway to ensure that they are up and running. If they are not, restart the Cisco Prime Infrastructure server and the Cisco Plug and Play Gateway.
  • Make sure that proper IP connectivity exists between your laptop and the Cisco Prime Infrastructure server and the Cisco Plug and Play Gateway.

Deployment server not configured. Configure the deployment server before you begin downloading the configuration.

Message type:
Error message.

Symptom:
This error is seen when the bootstrap configuration download prompts you to use a valid PIN.

Solution:
Before downloading the bootstrap configuration, make sure that you configure the Cisco Prime Infrastructure and the Cisco Plug and Play Gateway fields on the Settings page.

Communication Failed. Check the Plug and Play Gateway settings and the server status.

Message Type:
Error message

Symptom:
This error is seen when you try to save the Settings information and it fails.

Solution:

  • Verify that the Cisco Prime Infrastructure and Cisco Plug and Play Gateway are up and running. If they are not, restart the server.
  • Make sure that proper IP connectivity exists between your laptop and the Cisco Prime Infrastructure server and Cisco Plug and Play Gateway.

SSL certificate store save failed (or) Connection or SSL certificate download failed to the server

Message Type:
Error message

Symptom:
This error message is seen when the bootstrap download is requested using a PIN.

Solution:
Verify that the Cisco Prime Infrastructure and Cisco Plug and Play Gateway are up and running. If they are not, restart the server.
Make sure that proper IP connectivity exists between your laptop and the Cisco Prime Infrastructure and Cisco Plug and Play Gateway.
If the Cisco Plug and Play HTTPS port is configured with non-default, reconfigure the application settings with the correct HTTPS port.

Deploy option is not enabled even after connecting the Cisco Plug and Play Application with the device

Message Type:

NA

Symptom:

This error is seen when the necessary drivers are not installed for the USB Console cable.

Solution:

You must manually install the necessary drivers for the USB Console cable, and then connect the cable.

Logging in to the device even after disconnecting the cable

Message Type:

NA

Symptom:

The user removes the USB Console cable while the Cisco Plug and Play Application is still connected to the device. The Cisco Plug and Play Application displays a message that it is connecting/logging in to the device. This happens because the connector acts as a proxy for the Cisco Plug and Play Application.

Solution:

Close the Cisco Plug and Play Application and open it again.

Device Deployment failed

Message type:

Error Message

Symptom:

The Cisco Plug and Play Application deploys all the configured CLIs to the device and waits for the CNS configuration initial to succeed. If the CNS configuration initial is not initiated due to device issues, the Cisco Plug and Play Application will wait for two mins to check if the initial configuration is initiated. After two mins, if the device has still not initiated the CNS configuration initial, the Cisco Plug and Play Application will display a message that the deployment has failed.

Solution:

You must troubleshoot to assess the possible reasons for CNS initial not being triggered.

Deployment failed, but the device configuration is not reset to initial state

Message Type:

NA

Symptom:

When deployment fails due to a valid reason, and the configuration on the device is not reset to its initial state.

Solution:

The Cisco Plug and Play Application will back up the configuration, and reset only on factory default routers (day zero). Resetting to the factory default state is not done on day1 devices.

Rating: 0.0/5 (0 votes cast)

Personal tools