Cisco Nexus 7000 Series NX-OS Troubleshooting Guide -- Troubleshooting Installs, Upgrades, and Reboots
m (Cisco Nexus 7000 Series NX-OS Troubleshooting Guide, Release 4.x -- Troubleshooting Installs, Upgrades, and Reboots moved to Cisco Nexus 7000 Series NX-OS Troubleshooting Guide -- Troubleshooting Installs, Upgrades, and Reboots)
Revision as of 17:08, 30 April 2010
This article describes how to identify and resolve problems that might occur when upgrading or restarting.
Troubleshooting Installs, Upgrades, and Reboots (this section)
Before Contacting Technical Support
Troubleshooting Tools and Methodology
Information About Upgrades and Reboots
Cisco NX-OS consists of two images--the kickstart image and the system image. In order to bring up the system, both images should have the same image version.
Upgrades and reboots are ongoing network maintenance activities. You should try to minimize the risk of disrupting the network when performing these operations in production environments and to know how to recover quickly when something does go wrong.
|Note:||This publication used the term upgrade to refer to both Cisco NX-OS upgrades and downgrades.|
Upgrades and Reboot Checklist
Use the following checklist to prepare for an upgrade:
|Read the Release Notes for the release that you are upgrading or downgrading to.|
|Ensure that an FTP or TFTP server is available to download the software images.|
|Copy the new image onto your supervisor modules in bootflash: or slot0:.|
|Use the show install all impact command to verify that the new image is healthy and the impact that the new load will have on any hardware with regards to compatibility. Check for compatibility.|
|Copy the startup-config file to a snapshot configuration in NVRAM. This step creates a backup copy of the startup-config file (see the Rollback chapter in the Cisco NX-OS System Management Configuration Guide, Release 4.0).|
|Save your running configuration to the startup configuration.|
|Back up a copy of your configuration to a remote TFTP server.|
|Schedule your upgrade during an appropriate maintenance window for your network.|
After you have completed the checklist, you are ready to upgrade the systems in your network.
|Note:||It is normal for the active supervisor to become the standby supervisor during an upgrade.|
Verifying Software Upgrades
You can use the show install all status command to watch the progress of your software upgrade or to view the ongoing install all command or the log of the last installed install all command from a console, SSH, or Telnet session. This command shows the install all output on both the active and standby supervisor module even if you are not connected to the console terminal.
switch# show install all status There is an on-going installation... <---------------------- in progress installation Enter Ctrl-C to go back to the prompt. Verifying image bootflash:/b-126.96.36.199 -- SUCCESS Verifying image bootflash:/i-188.8.131.52 -- SUCCESS Extracting system version from image bootflash:/i-184.108.40.206. -- SUCCESS Extracting kickstart version from image bootflash:/b-220.127.116.11. -- SUCCESS Extracting loaderâ version from image bootflash:/b-18.104.22.168. -- SUCCESS
switch# show install all status This is the log of last installation. <----------------- log of last install Verifying image bootflash:/b-22.214.171.124 -- SUCCESS Verifying image bootflash:/i-126.96.36.199 -- SUCCESS Extracting system version from image bootflash:/i-188.8.131.52. -- SUCCESS Extracting kickstart version from image bootflash:/b-184.108.40.206. -- SUCCESS Extracting loader version from image bootflash:/b-220.127.116.11. -- SUCCESS
Verifying a Nondisruptive Upgrade
When you initiate a nondisruptive upgrade, Cisco NX-OS notifies all services that an upgrade is about to start and finds out whether or not the upgrade can proceed. If a service cannot allow the upgrade to proceed at this time, then the service aborts the upgrade and you are prompted to enter the show install all failure-reason command to determine the reason why the upgrade cannot proceed.
Do you want to continue with the installation (y/n)? [n] y Install is in progress, please wait. Notifying services about the upgrade. >[# ] 0% -- FAIL. Return code 0x401E0066 (request timed out). Please issue "show install all failure-reason" to find the cause of the failure.<---prompt failure-reason Install has failed. Return code 0x401E0066 (request timed out). Please identify the cause of the failure, and try 'install all' again.
switch# show install all failure-reason Service: "cfs" failed to respond within the given time period. switch#
If a failure occurs for whatever reason (such as a save runtime state failure or module upgrade failure) after the upgrade is in progress, then the device reboots disruptively because the changes cannot be rolled back. In such cases, the upgrade has failed.
If you need further assistance to determine why an upgrade is unsuccessful, you should collect the details from the show tech-support command output and the console output from the installation, if available, before you contact your technical support representative.
Using ROM Monitor Mode
If your device does not find a valid system image to load, the system will start in ROM monitor mode. ROM monitor mode can also be accessed by interrupting the boot sequence during startup. From ROM monitor mode, you can boot the device or perform diagnostic tests.
On most systems, you can enter ROM monitor mode by entering the reload EXEC command and then pressing the Break key on your keyboard or by using the Break key-combination (the default Break key combination is Ctrl-C) during the first 60 seconds of startup.
Troubleshooting Software Upgrades and Downgrades
This section describes how to troubleshoot a software installation upgrade or downgrade failure.
Software Upgrade Ends with Error
|The upgrade ends with an error.||The standby supervisor module bootflash: file system does not have sufficient space to accept the updated image.||Use the delete command to remove unnecessary files from the file system.|
|The specified system and kickstart images are not compatible.||Check the output of the installation process for details on the incompatibility. Possibly update the kickstart image before updating the system image.|
|The install all command is entered on the standby supervisor module.||Enter the command on the active supervisor module only.|
|A module was inserted while the upgrade was in progress.||Restart the installation.|
|The system experienced a power disruption while the upgrade was in progress.||Restart the installation.|
|An incorrect software image path was specified.||Specify the entire path for the remote location accurately.|
|Another upgrade is already in progress.||Verify the state of the system at every stage and restart the upgrade after 10 seconds. If you restart the upgrade within 10 seconds, the command is rejected. An error message displays, indicating that an upgrade is currently in progress.|
|Module failed to upgrade.||Restart the upgrade or use the install module command to upgrade the failed module.|
Upgrading Cisco NX-OS Software
To perform an automated software upgrade on any system from the CLI, follow these steps:
- Log into the system through the console, Telnet, or SSH port of the active supervisor.
- Create a backup of your existing configuration file, if required.
- Perform the upgrade by entering the install all command.
- Exit the system console and open a new terminal session to view the upgraded supervisor module by using the show module command.
Tip: Always carefully read the output of the install all compatibility check command. This compatibility check tells you exactly what needs to be upgraded (such as the BIOS, loader, or firmware) and what modules will experience a disruptive upgrade. If there are any questions or concerns about the results of the output, type n to stop the installation and contact the next level of support.
The following example shows an upgrade using the install all command with the source images located on an SCP server.
switch# install all system scp://testuser@tftp-server1/tftpboot/rel/qa/4.0/final/m95 00-sf1ek9-mz.4.0.bin kickstart scp://testuser@tftp-server1/tftpboot/rel/qa/4.0/fin al/n7000-s1-kickstart-mz.4.0.bin
For scp://testuser@tftp-server1, please enter password: For scp://testuser@tftp-server1, please enter password: Copying image from scp://testuser@pal/tftpboot/rel/qa/4.0/final/n7000-s1 -kickstart-mz.4.0.bin to bootflash:///n7000-s1-kickstart-mz.4.0.bin. [####################] 100% -- SUCCESS Copying image from scp://testuser@pal/tftpboot/rel/qa/4.0/final/n7000-s1 -mz.4.0.bin to bootflash:///n7000-s1-mz.4.0.bin. [####################] 100% -- SUCCESS Verifying image bootflash:///n7000-s1-kickstart-mz.4.0.bin [####################] 100% -- SUCCESS Verifying image bootflash:///n7000-s1-mz.4.0.bin [####################] 100% -- SUCCESS Extracting "slc" version from image bootflash:///n7000-s1-mz.4.0.bin. [####################] 100% -- SUCCESS Extracting "ips" version from image bootflash:///n7000-s1-mz.4.0.bin. [####################] 100% -- SUCCESS Extracting "svclc" version from image bootflash:///n7000-s1-mz.4.0.bin. [####################] 100% -- SUCCESS Extracting "system" version from image bootflash:///n7000-s1-mz.4.0.bin. [####################] 100% -- SUCCESS Extracting "kickstart" version from image bootflash:///n7000-s1-kickstart-mz .4.0.bin. [####################] 100% -- SUCCESS Extracting "loader" version from image bootflash:///n7000-s1-kickstart-mz.2. 1.1a.bin. [####################] 100% -- SUCCESS Compatibility check is done: Module bootable Impact Install-type Reason ------ -------- -------------- ------------ ------ 1 yes non-disruptive rolling 2 yes non-disruptive rolling 3 yes disruptive rolling Hitless upgrade is not supported 4 yes disruptive rolling Hitless upgrade is not supported 5 yes non-disruptive reset 6 yes non-disruptive reset Images will be upgraded according to following table: Module Image Running-Version New-Version Upg-Required ------ ---------- -------------------- -------------------- ------------ 1 slc 2.0(2b) 2.1(1a) yes 1 bios v1.1.0(10/24/03) v1.1.0(10/24/03) no 2 slc 2.0(2b) 2.1(1a) yes 2 bios v1.1.0(10/24/03) v1.1.0(10/24/03) no 3 ips 2.0(2b) 2.1(1a) yes 3 bios v1.1.0(10/24/03) v1.1.0(10/24/03) no 4 svclc 2.0(2b) 2.1(1a) yes 4 svcsb 1.3(5m) 1.3(5m) no 4 svcsb 1.3(5m) 1.3(5m) no 4 bios v1.1.0(10/24/03) v1.1.0(10/24/03) no 5 system 2.0(2b) 2.1(1a) yes 5 kickstart 2.0(2b) 2.1(1a) yes 5 bios v1.1.0(10/24/03) v1.1.0(10/24/03) no 5 loader 1.2(2) 1.2(2) no 6 system 2.0(2b) 2.1(1a) yes 6 kickstart 2.0(2b) 2.1(1a) yes 6 bios v1.1.0(10/24/03) v1.1.0(10/24/03) no 6 loader 1.2(2) 1.2(2) no Do you want to continue with the installation (y/n)? [n] '''y''' Install is in progress, please wait. Syncing image bootflash:///n7000-s1-kickstart-mz.4.0.bin to standby. [####################] 100% -- SUCCESS Syncing image bootflash:///n7000-s1-mz.4.0.bin to standby. [####################] 100% -- SUCCESS Setting boot variables. [####################] 100% -- SUCCESS Performing configuration copy. [####################] 100% -- SUCCESS Module 5: Waiting for module online. 2005 May 20 15:46:03 ca-9506 %KERN-2-SYSTEM_MSG: mts: HA communication with standby terminated. Please check the standby supervisor. -- SUCCESS "Switching over onto standby".
If the configuration meets all guidelines when the install all command is used, all modules (supervisor and switching) are upgraded.
Troubleshooting Software System Reboots
This section describes how to troubleshoot software reboots.
Power-On or Switch Reboot Hangs
|A power-on or switch reboot hangs for a dual supervisor configuration.||The bootflash is corrupted.||Use the Recovery for Systems with Dual Supervisor Modules procedure.|
|The BIOS is corrupted.||Replace this module. Contact your customer support representative to return the failed module.|
|The kickstart image is corrupted.||Power cycle the switch if required and enter CTRL-C when the switch says "Loading Boot Loader" to interrupt the boot process at the >loader prompt. Use the Recovery from the loader> Prompt on Supervisor Modules procedure to update the kickstart image.|
|Boot parameters are incorrect.||Verify and correct the boot parameters and reboot.|
|The system image is corrupted.||Power cycle the switch if required and enter CTRL-] when the switch says "Checking all filesystems....r. done." to interrupt the boot process at the switch#boot prompt. Use the Recovery from the switch(boot)# Prompt procedure to update the system image..|
Corrupted Bootflash Recovery
All device configurations reside in the internal bootflash. If you have a corrupted internal bootflash, you could potentially lose your configuration. Be sure to save and back up your configuration files periodically. The regular system boot goes through the following sequence (see Figure 1):
- The basic input/output system (BIOS) loads the loader.
- The loader loads the kickstart image into RAM and starts the kickstart image.
- The kickstart image loads and starts the system image.
- The system image reads the startup-configuration file.
Figure 1 Regular Boot Sequence
If the images on your system are corrupted and you cannot proceed (error state), you can interrupt the system boot sequence and recover the image by entering the BIOS configuration utility described in the following section. Access this utility only when needed to recover a corrupted internal disk.
|Caution:||The BIOS changes explained in this section are required only to recover a corrupted bootflash.|
Recovery procedures require the regular sequence to be interrupted. The internal sequence goes through four phases between the time that you turn on the system and the time that the system prompt appears on your terminal--BIOS, boot loader, kickstart, and system.
| Recovery Interruption
|Phase||Normal Prompt--appears at the end of each phase.||Recovery Prompt--appears when the system cannot progress to the next phase.||Description|
|BIOS||loader>||No bootable device||The BIOS begins the power-on self test, memory test, and other operating system applications. While the test is in progress, press Ctrl-C to enter the BIOS configuration utility and use the netboot option.|
|Boot loader||Starting kickstart||loader>||The boot loader uncompresses the loaded software to boot an image using its filename as a reference. These images are made available through bootflash. When the memory test is over, press Esc to enter the boot loader prompt.|
|Kickstart||Uncompressing system||switch(boot)#||When the boot loader phase is over, press Ctrl-] (Control key plus right bracket key) to enter the switch(boot)# prompt. Depending on your Telnet client, these keys may be reserved, and you may need to remap the keystroke. See the documentation provided by your Telnet client. If the corruption causes the console to stop at this prompt, copy the system image and reboot the system.|
|System||Login:||--||The system image loads the configuration file of the last saved running configuration and returns a switch login prompt.|
Figure 2 Regular and Recovery Sequence
Recovery from the loader> Prompt on Supervisor Modules
|Caution:||This procedure uses the init system command, which reformats the file system of the device. Be sure that you have made a backup of the configuration files before you begin this procedure.|
The loader> prompt is different from the regular switch# prompt. The CLI command completion feature does not work at the loader> prompt and may result in undesired errors. You must type the command exactly as you want the command to appear.
Use the help command at the loader> prompt to display a list of commands available at this prompt or to obtain more information about a specific command in that list.
To recover a corrupted kickstart image (system error state) for a system with a single supervisor module, follow these steps:
1. Enter the local IP address and subnet mask for the system at the loader> prompt, and press Enter.
loader> set ip 172.16.1.2 255.255.255.0
2. Specify the IP address of the default gateway.
loader> set gw 172.16.1.1
3. Boot the kickstart image file from the required server.
loader> boot tftp://172.16.10.100/tftpboot/n7000-s1-kickstart-4.0.bin
In this example, 172.16.10.100 is the IP address of the TFTP server, and n7000-s1-kickstart-4.0.bin is the name of the kickstart image file that exists on that server.
The switch(boot)# prompt indicates that you have a usable Kickstart image.
4. Enter the init system command at the switch(boot)# prompt.
switch(boot)# init system
|Caution:||Be sure that you have made a backup of the configuration files before you enter this command.|
5. Follow the procedure specified in the Recovery from the switch(boot)# Prompt procedure.
Recovery from the loader> Prompt
Tip: Use the help command at the loader> prompt to display a list of commands available at this prompt or to obtain more information about a specific command in that list.
1. Specify the local IP address and the subnet mask for the system.
loader> set ip 172.21.55.213 255.255.255.224 set ip 172.21.55.213 255.255.255.224 Correct - ip addr is 172.21.55.213, mask is 255.255.255.224 Found Intel 82546GB [2:9.0] at 0xe040, ROM address 0xf980 Probing...[Intel 82546GB] Management interface Link UP in 1000/full mode Ethernet addr: 00:1B:54:C1:28:60 Address: 172.21.55.213 Netmask: 255.255.255.224 Server: 0.0.0.0 Gateway: 172.21.55.193
2. Specify the IP address of the default gateway.
loader> set gw 172.21.55.193 Correct gateway addr 172.21.55.193 Address: 172.21.55.213 Netmask: 255.255.255.224 Server: 0.0.0.0 Gateway: 172.21.55.193
3. Boot the kickstart image file from the required server.
loader> loader> '''boot tftp://172.28.255.18/tftpboot/n7000-s1-kickstart.4.0.3.gbin ''' Address: 172.21.55.213 Netmask: 255.255.255.224 Server: 172.28.255.18 Gateway: 172.21.55.193 Filesystem type is tftp, using whole disk Booting: /tftpboot/n7000-s1-kickstart.4.0.3.gbin console=ttyS0,9600n8nn quiet loader _ver="3.17.0".... .............................................................................Im age verification OK Starting kernel... INIT: version 2.85 booting Checking all filesystems..r.r.r.. done. Setting kernel variables: sysctlnet.ipv4.ip_forward = 0 net.ipv4.ip_default_ttl = 64 net.ipv4.ip_no_pmtu_disc = 1 . Setting the System Clock using the Hardware Clock as reference...System Clock set. Local time: Wed Oct 1 11:20:11 PST 2008 WARNING: image sync is going to be disabled after a loader netboot Loading system software No system image Unexporting directories for NFS kernel daemon...done. INIT: Sending processes the KILL signal Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Copyright (c) 2002-2008, Cisco Systems, Inc. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under license. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or the GNU Lesser General Public License (LGPL) Version 2.1. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://www.opensource.org/licenses/lgpl-2.1.php switch(boot)#
The switch(boot)# prompt indicates that you have a usable kickstart image.
4. Enter the init system command at the switch(boot)# prompt.
switch(boot)# init system
|Caution:||Be sure that you have made a backup of the configuration files before you enter this command.|
5. Follow the procedure specified in the Recovery from the switch(boot)# Prompt.
Recovery from the switch(boot)# Prompt
To recover a system image using the kickstart image for a system with a single supervisor module, follow these steps:
1. Change to configuration mode and configure the IP address of the mgmt0 interface.
switch(boot)# config t switch(boot)(config)# interface mgmt0
2. Follow this step if you entered an init system command. Otherwise, skip to Step 3.
a. Enter the ip address command to configure the local IP address and the subnet mask for the system.
switch(boot)(config-mgmt0)# ip address 172.16.1.2 255.255.255.0
b. Enter the ip default-gateway command to configure the IP address of the default gateway.
switch(boot)(config-mgmt0)# ip default-gateway 172.16.1.1
3. Enter the no shutdown command to enable the mgmt0 interface on the system.
switch(boot)(config-mgmt0)# no shutdown
4. Enter end to exit to EXEC mode.
5. If you believe there are file system problems, enter the init system check-filesystem command. This command checks all internal file systems and fixes any errors that are encountered. This command takes a few minutes to complete.
switch(boot)# init system check-filesytem
6. Copy the system image from the required TFTP server.
switch(boot)# copy tftp://172.16.10.100/system-image1 bootflash:system-image1
7. Copy the kickstart image from the required TFTP server.
switch(boot)# copy tftp://172.16.10.100/kickstart-image1 bootflash:kickstart-image1
8. Verify that the system and kickstart image files are copied to your bootflash: file system.
switch(boot)#''' dir bootflash: ''' 12456448 Jul 30 23:05:28 1980 kickstart-image1 12288 Jun 23 14:58:44 1980 lost+found/ 27602159 Jul 30 23:05:16 1980 system-image1 Usage for bootflash://sup-local 135404544 bytes used 49155072 bytes free 184559616 bytes total
9. Load the system image from the bootflash: files system.
switch(boot)# '''load bootflash:system-image1''' Uncompressing system image: bootflash:/system-image1 CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC Would you like to enter the initial configuration mode? (yes/no): yes
|Note:||If you enter no, you will return to the switch# login prompt, and you must manually configure the system.|
Recovery for Systems with Dual Supervisor Modules
This section describes how to recover when one or both supervisor modules in a dual supervisor system have corrupted bootflash.
Recovering One Supervisor Module With Corrupted Bootflash
If one supervisor module has a functioning bootflash and the other has a corrupted bootflash, follow these steps:
- Boot the functioning supervisor module and log on to the system.
- At the switch# prompt on the booted supervisor module, enter the reload module slot force-dnld command, where slot is the slot number of the supervisor module with the corrupted bootflash.
The supervisor module with the corrupted bootflash performs a netboot and checks the bootflash for corruption. When the bootup scripts discover that the bootflash is corrupted, it generates an init system command, which fixes the corrupt bootflash. The supervisor boots as the HA Standby.
Recovering Both Supervisor Modules with Corrupted Bootflash
If both supervisor modules have corrupted bootflash, follow these steps:
1. Boot the system and press the Esc key after the BIOS memory test to interrupt the boot loader.
You see the loader> prompt.
2. Specify the local IP address and the subnet mask for the system.
3. Specify the IP address of the default gateway.
4. Boot the kickstart image file from the required server.
The switch(boot)# prompt indicates that you have a usable kickstart image.
5. Enter the init-system command to repartition and format the bootflash.
6. Perform the steps in the Recovery from the switch(boot)# Prompt procedure.
7. Perform the steps in the Recovering One Supervisor Module With Corrupted Bootflash procedure to recover the other supervisor module.
|Note:||If you do not enter the reload module command when a boot failure has occurred, the active supervisor module automatically reloads the standby supervisor module within 3 to 6 minutes after the failure.|
System or Process Resets
When a recoverable or nonrecoverable error occurs, the system or a process on the system may reset. See Table 2-4 for possible causes and solutions.
|The system or a process on the system resets.||A recoverable error occurred on the system or on a process in the system.||The system has automatically recovered from the problem. Use the Recoverable System Restarts procedure and the System or Process Resets procedure.|
|A nonrecoverable error occurred on the system.||The system cannot recover automatically from the problem. Use the Recoverable System Restarts procedure to determine the cause.|
|A clock module failed.||Verify that a clock module failed. Replace the failed clock module during the next maintenance window.|
Recoverable System Restarts
Every process restart generates a syslog message and a Call Home event. Even if the event does not affect service, you should identify and resolve the condition immediately because future occurrences could cause a service interruption.
To respond to a recoverable system restart, follow these steps:
1. Check the syslog file to see which process restarted and why it restarted.
switch# show log logfile | include error
For information about the meaning of each message, see the Cisco NX-OS System Messages Reference. The system output looks like the following example:
Sep 10 23:31:31 dot-6 % LOG_SYSMGR-3-SERVICE_TERMINATED: Service "sensor" (PID 704) has finished with error code SYSMGR_EXITCODE_SY. switch# show logging logfile | include fail Jan 27 04:08:42 88 %LOG_DAEMON-3-SYSTEM_MSG: bind() fd 4, family 2, port 123, ad dr 0.0.0.0, in_classd=0 flags=1 fails: Address already in use Jan 27 04:08:42 88 %LOG_DAEMON-3-SYSTEM_MSG: bind() fd 4, family 2, port 123, ad dr 127.0.0.1, in_classd=0 flags=0 fails: Address already in use Jan 27 04:08:42 88 %LOG_DAEMON-3-SYSTEM_MSG: bind() fd 4, family 2, port 123, ad dr 127.1.1.1, in_classd=0 flags=1 fails: Address already in use Jan 27 04:08:42 88 %LOG_DAEMON-3-SYSTEM_MSG: bind() fd 4, family 2, port 123, ad dr 172.22.93.88, in_classd=0 flags=1 fails: Address already in use Jan 27 23:18:59 88 % LOG_PORT-5-IF_DOWN: Interface fc1/13 is down (Link failure or not-connected) Jan 27 23:18:59 88 % LOG_PORT-5-IF_DOWN: Interface fc1/14 is down (Link failure or not-connected) Jan 28 00:55:12 88 % LOG_PORT-5-IF_DOWN: Interface fc1/1 is down (Link failure o r not-connected) Jan 28 00:58:06 88 % LOG_ZONE-2-ZS_MERGE_FAILED: Zone merge failure, Isolating p ort fc1/1 (VSAN 100) Jan 28 00:58:44 88 % LOG_ZONE-2-ZS_MERGE_FAILED: Zone merge failure, Isolating p ort fc1/1 (VSAN 100) Jan 28 03:26:38 88 % LOG_ZONE-2-ZS_MERGE_FAILED: Zone merge failure, Isolating p ort fc1/1 (VSAN 100) Jan 29 19:01:34 88 % LOG_PORT-5-IF_DOWN: Interface fc1/1 is down (Link failure o r not-connected) switch#
2. Identify the processes that are running and the status of each process.
switch# show processes
The following codes are used in the system output for the state (process state):
- D = uninterruptible sleep (usually I/O)
- R = runnable (on run queue)
- S = sleeping
- T = traced or stopped
- Z = defunct (zombie) process
- NR = notrunning
- ER = should be running but currently notrunning
|Note:||ER usually is the state that a process enters if it has been restarted too many times and has been detected as faulty by the system and disabled.|
The system output looks like the following example. (This output has been abbreviated to be more concise.)
PID State PC Start_cnt TTY Process ----- ----- -------- ----------- ---- ------------- 1 S 2ab8e33e 1 - init 2 S 0 1 - keventd 3 S 0 1 - ksoftirqd_CPU0 4 S 0 1 - kswapd 5 S 0 1 - bdflush 6 S 0 1 - kupdated 71 S 0 1 - kjournald 136 S 0 1 - kjournald 140 S 0 1 - kjournald 431 S 2abe333e 1 - httpd 443 S 2abfd33e 1 - xinetd 446 S 2ac1e33e 1 - sysmgr 452 S 2abe91a2 1 - httpd 453 S 2abe91a2 1 - httpd 456 S 2ac73419 1 S0 vsh 469 S 2abe91a2 1 - httpd 470 S 2abe91a2 1 - httpd
3. Show the processes that have had abnormal exits and to if there is a stack-trace or core dump.
switch# show process log Process PID Normal-exit Stack-trace Core Log-create-time ---------------- ------ ----------- ----------- ------- --------------- ntp 919 N N N Jan 27 04:08 snsm 972 N Y N Jan 24 20:50
4. Show detailed information about a specific process that has restarted.
switch# show processes log pid 898 Service: idehsd Description: ide hotswap handler Daemon Started at Mon Sep 16 14:56:04 2002 (390923 us) Stopped at Thu Sep 19 14:18:42 2002 (639239 us) Uptime: 2 days 23 hours 22 minutes 22 seconds Start type: SRV_OPTION_RESTART_STATELESS (23) Death reason: SYSMGR_DEATH_REASON_FAILURE_SIGTERM (3) Exit code: signal 15 (no core) CWD: /var/sysmgr/work Virtual Memory: CODE 08048000 - 0804D660 DATA 0804E660 - 0804E824 BRK 0804E9A0 - 08050000 STACK 7FFFFD10 Register Set: EBX 00000003 ECX 0804E994 EDX 00000008 ESI 00000005 EDI 7FFFFC9C EBP 7FFFFCAC EAX 00000008 XDS 0000002B XES 0000002B EAX 00000003 (orig) EIP 2ABF5EF4 XCS 00000023 EFL 00000246 ESP 7FFFFC5C XSS 0000002B Stack: 128 bytes. ESP 7FFFFC5C, TOP 7FFFFD10 0x7FFFFC5C: 0804F990 0804C416 00000003 0804E994 ................ 0x7FFFFC6C: 00000008 0804BF95 2AC451E0 2AAC24A4 .........Q.*.$.* 0x7FFFFC7C: 7FFFFD14 2AC2C581 0804E6BC 7FFFFCA8 .......*........ 0x7FFFFC8C: 7FFFFC94 00000003 00000001 00000003 ................ 0x7FFFFC9C: 00000001 00000000 00000068 00000000 ........h....... 0x7FFFFCAC: 7FFFFCE8 2AB4F819 00000001 7FFFFD14 .......*........ 0x7FFFFCBC: 7FFFFD1C 0804C470 00000000 7FFFFCE8 ....p........... 0x7FFFFCCC: 2AB4F7E9 2AAC1F00 00000001 08048A2C ...*...*....,... PID: 898 SAP: 0 UUID: 0 switch#
5. Determine if the restart recently occurred.
switch# show system uptime Start Time: Fri Sep 13 12:38:39 2002 Up Time: 0 days, 1 hours, 16 minutes, 22 seconds
To determine if the restart is repetitive or a one-time occurrence, compare the length of time that the system has been up with the time stamp of each restart.
6. View the core files.
switch# show cores Module-num Process-name PID Core-create-time ---------- ------------ --- ---------------- 5 fspf 1524 Jan 9 03:11 6 fcc 919 Jan 9 03:09 8 acltcam 285 Jan 9 03:09 8 fib 283 Jan 9 03:08
The output shows all cores that are presently available for upload from the active supervisor. The module-num column shows the slot number on which the core was generated. In the previous example, an FSPF core was generated on the active supervisor module in slot 5. An FCC core was generated on the standby supervisory module in slot 6. Core dumps generated on the module in slot 8 include ACLTCAM and FIB.
Copy the FSPF core dump to a TFTP server with the IP address 18.104.22.168, as follows:
switch# copy core://5/1524 tftp::/22.214.171.124/abcd
Display the file named zone_server_log.889 in the log directory as follows:
switch# '''show pro log pid 1473''' ====================================================== Service: ips Description: IPS Manager Started at Tue Jan 8 17:07:42 1980 (757583 us) Stopped at Thu Jan 10 06:16:45 1980 (83451 us) Uptime: 1 days 13 hours 9 minutes 9 seconds Start type: SRV_OPTION_RESTART_STATELESS (23) Death reason: SYSMGR_DEATH_REASON_FAILURE_SIGNAL (2) Exit code: signal 6 (core dumped) CWD: /var/sysmgr/work Virtual Memory: CODE 08048000 - 080FB060 DATA 080FC060 - 080FCBA8 BRK 081795C0 - 081EC000 STACK 7FFFFCF0 TOTAL 20952 KB Register Set: EBX 000005C1 ECX 00000006 EDX 2AD721E0 ESI 2AD701A8 EDI 08109308 EBP 7FFFF2EC EAX 00000000 XDS 0000002B XES 0000002B EAX 00000025 (orig) EIP 2AC8CC71 XCS 00000023 EFL 00000207 ESP 7FFFF2C0 XSS 0000002B Stack: 2608 bytes. ESP 7FFFF2C0, TOP 7FFFFCF0 0x7FFFF2C0: 2AC8C944 000005C1 00000006 2AC735E2 D..*.........5.* 0x7FFFF2D0: 2AC8C92C 2AD721E0 2AAB76F0 00000000 ,..*.!.*.v.*.... 0x7FFFF2E0: 7FFFF320 2AC8C920 2AC513F8 7FFFF42C ... ..*...*,... 0x7FFFF2F0: 2AC8E0BB 00000006 7FFFF320 00000000 ...*.... ....... 0x7FFFF300: 2AC8DFF8 2AD721E0 08109308 2AC65AFC ...*.!.*.....Z.* 0x7FFFF310: 00000393 2AC6A49C 2AC621CC 2AC513F8 .......*.!.*...* 0x7FFFF320: 00000020 00000000 00000000 00000000 ............... 0x7FFFF330: 00000000 00000000 00000000 00000000 ................ 0x7FFFF340: 00000000 00000000 00000000 00000000 ................ 0x7FFFF350: 00000000 00000000 00000000 00000000 ................ 0x7FFFF360: 00000000 00000000 00000000 00000000 ................ 0x7FFFF370: 00000000 00000000 00000000 00000000 ................ 0x7FFFF380: 00000000 00000000 00000000 00000000 ................ 0x7FFFF390: 00000000 00000000 00000000 00000000 ................ 0x7FFFF3A0: 00000002 7FFFF3F4 2AAB752D 2AC5154C . ... output abbreviated ... Stack: 128 bytes. ESP 7FFFF830, TOP 7FFFFCD0
7. Enter the system cores tftp:[//servername][/path] command to configure the system to use TFTP to send the core dump to a TFTP server.
This command causes the system to enable the automatic copy of core files to a TFTP server. For example, the following command sends the core files to the TFTP server with the IP address 10.1.1.1:
switch(config)# system cores tftp://10.1.1.1/cores
The following conditions apply:
- The core files are copied every 4 minutes. This time interval is not configurable.
- The copy of a specific core file to a TFTP server can be manually triggered, by using the command copy core://module#/pid# tftp://tftp_ip_address/file_name.
- The maximum number of times that a process can be restarted is part of the high-availability (HA) policy for any process. (This parameter is not configurable.) If the process restarts more than the maximum number of times, the older core files are overwritten.
- The maximum number of core files that can be saved for any process is part of the HA policy for any process. (This parameter is not configurable, and it is set to three.)
8. Determine the cause and resolution for the restart condition by contacting your technical support representative and asking the representative to review your core dump.
See the Cisco NX-OS High Availability and Redundancy Guide, Release 4.0 for more information on high-availability policies.
Unrecoverable System Restarts
An unrecoverable system restart might occur in the following cases:
- A critical process fails and is not restartable.
- A process restarts more times than is allowed by the system configuration.
- A process restarts more frequently than is allowed by the system configuration.
The effect of a process reset is determined by the policy configured for each process. An unrecoverable reset may cause functionality loss, the active supervisor to restart, a supervisor switchover, or the system to restart.
To respond to an unrecoverable reset, see the Troubleshooting Cisco NX-OS Software System Reboots procedure.
The show system reset-reason command displays the following information:
- The last four reset-reason codes for the supervisor modules are displayed. If either supervisor module is absent, the reset-reason codes for that supervisor module are not displayed.
- The show system reset-reason module number command displays the last four reset-reason codes for a specific module in a given slot. If a module is absent, then the reset-reason codes for that module are not displayed.
- The overall history of when and why expected and unexpected reloads occur
- The time stamp of when the reset or reload occurred
- The reason for the reset or reload of a module
- The service that caused the reset or reload (not always available)
- The software version that was running at the time of the reset or reload
switch# show system reset-reason module 6 ----- reset reason for Supervisor-module 6 (from Supervisor in slot 6) --- 1) At 281000 usecs after Wed Jun 25 20:16:34 2008 Reason: Reset Requested by CLI command reload Service: Version: 4.0(2.45) 2) At 791071 usecs after Wed Jun 25 20:04:50 2008 Reason: Reset Requested by CLI command reload Service: Version: 4.0(2.45) 3) At 70980 usecs after Wed Jun 25 19:55:52 2008 Reason: Reset Requested by CLI command reload Service: Version: 4.0(2) 4) At 891463 usecs after Wed Jun 18 23:44:48 2008 Reason: Reset Requested by CLI command reload Service: Version: 4.0(2)
Standby Supervisor Fails to Boot
The standby supervisor does not boot after an upgrade. You may see the following system message:
- Error Message SYSMGR-2-STANDBY_BOOT_FAILED: Standby supervisor failed to boot up.
- Explanation This message is printed if the standby supervisor doesn't complete its boot procedure (i.e. it doesn't reach the login prompt on the local console) 3 to 6 minutes after the loader has been loaded by the BIOS. This message is usually caused by boot variables not properly set for the standby supervisor. This message can also be caused by a user intentionally interrupting the boot procedure at the loader prompt (by means of pressing ESC).
- Recommended Action Connect to the local console of the standby supervisor. If the supervisor is at the loader prompt, try to use the boot command to continue the boot procedure. Otherwise, issue a reload command for the standby supervisor from a vsh session on the active supervisor, specifying the force-dnld option. Once the standby is online, fix the problem by setting the boot variables appropriately.
|Standby supervisor does not boot.||Active supervisor kickstart image booted from TFTP.||Reload the active supervisor from bootflash:.|
Recovering the Administrator Password
You can access the system if you forget the administrator password.
|You forgot the administrator password for accessing.||Use the Password Recovery procedure to recover the password using a local console connection.|
The following links contain further information on this topic from Cisco.com:
External links contain content developed by external authors. Cisco does not review this content for accuracy.