Cisco IP Transfer Point with GTT Application Group Overflow Load Sharing Configuration Example

From DocWiki

(Difference between revisions)
Jump to: navigation, search
m (Configuration)
m (Introduction)
 
(32 intermediate revisions not shown)
Line 1: Line 1:
-
{{Template:Required Metadata}}
 
-
<font size = "5">'''Configuring GTT Application Group Overflow Load Sharing for SCCP Class 0'''</font>
 
-
 
-
This configuration allows the ITP to send a user defined amount of traffic to a primary destination. Excess traffic is then sent to a secondary destination. This distribution is more specific than those based on congestion. Overflow load sharing is especially useful for enforcing customer limitations.
 
-
 
-
'''Restrictions and Considerations'''
 
-
 
-
* Only one rate limit entry is allowed for a GTT application group.
 
-
* You configure the rate limit entry for a specific destination in the GTT application group.
 
-
* You must configure both a primary and secondary (backup).
 
-
* You can define the primary and secondary by configuring ASs, DPCs, or any combination of an AS and DPC.
 
-
* The primary AS or DPC is defined as the one with the lowest configured cost.
 
-
'''CONFIGURATION STEPS'''
 
-
 
-
'''Command or Action'''
 
-
 
-
'''Purpose'''
 
-
*
 
-
<font size = "1">'''enable'''</font>
 
-
 
-
*
 
-
<font size = "1">Router> enable</font>
 
-
 
-
Enables privileged EXEC mode.
 
-
 
-
* Enter your password if prompted.
 
-
*
 
-
<font size = "1">'''configure terminal'''</font>
 
-
 
-
*
 
-
<font size = "1">Router# configure terminal</font>
 
-
 
-
Enters global configuration mode.
 
-
*
 
-
<font size = "1">'''cs7 gtt application-group '''''group-name''</font>
 
-
 
-
*
 
-
<font size = "1">Router(config)# cs7 gtt application-group abc</font>
 
-
 
-
Defines the GTT application group and enables application-group submode.
 
-
*
 
-
<font size = "1">'''multiplicity '''</font>{<font size = "1">'''cost '''</font>|<font size = "1">''' share | cgpa | wrr'''</font>}
 
-
 
-
*
 
-
<font size = "1">Router(config-cs7-gtt-app-grp)#  multiplicity cost</font>
 
-
 
-
Specifies a method for selecting a destination for the application group.
 
-
 
-
* '''cost'''—Uses the destination with the least cost if that destination is available.
 
-
* '''share'''—Shares equally among all destinations.
 
-
* '''cgpa'''—Uses the SCCP calling party address (CGPA) field, which results in a weighted factor selection number for choosing the next destination from the available items in the application group.
 
-
* '''wrr'''—Applies weighted round robin load balancing (WRR) to SCCP class 0 and SCCP class 1 traffic.
 
-
* The '''cost '''keyword is used for overflow load sharing configurations.
 
-
*
 
-
<font size = "1">[</font><font size = "1">'''instance''' ''instance-number''] '''asname''' ''as-name'' {''cost'' ['''ssn''' ''ssn''] {'''gt''' ['''ntt''' ''ntt''] | '''pcssn'''} ['''limit''' ''rate''] | ''wf'' ['''ssn''' ''ssn''] {'''gt''' ['''ntt''' ''ntt''] | '''pcssn'''}}</font>
 
-
 
-
*
 
-
 
-
The primary AS use the '''limit '''keyword and ''rate ''argument to define the rate limit.
 
-
 
-
<font size = "1">Router(config-cs7-gtt-app-grp)#  asname weekday 1 gt limit 2000</font>
 
-
 
-
The backup AS does not define a rate limit.
 
-
 
-
<font size = "1">Router(config-cs7-gtt-app-grp)# asname weekday overflow 2  gt </font>
 
-
 
-
(Optional) Assigns an M3UA or SUA AS directly to a global title.
 
-
 
-
You must configure both a primary and backup AS to take advantage of the GTT loadshare overflow feature.
 
-
 
-
You must assign a cost to the AS to take advantage of the GTT overflow loadsharing feature. The primary destination is defined by the lower cost.
 
-
 
-
* ''cost''—''' '''Index value (1-64). Specifies the priority of the AS within the application group.
 
-
Use the '''limit '''keyword to limit traffic rate to a specific AS in a GTT application group. The rate limit is configured only on the primary destination.
 
-
 
-
* '''limit'''—Specifies the traffic-rate limitation.
 
-
* ''rate''—defines the rate as an integer value from 1 to 4294967296 MSU/sec.
 
-
*
 
-
<font size = "1">[</font><font size = "1">'''instance''' ''instance-number''] '''pc''''' pc'' ['''ssn''' ''ssn''] {''cost'' {'''gt'''['''ntt''' ''ntt'']|'''pcssn'''} ['''limit''' ''rate''] | ''wf ''{'''gt''' ['''ntt''' ''ntt'']|'''pcssn'''}}</font>
 
-
 
-
*
 
-
 
-
The primary DPC use the '''limit '''keyword and ''rate ''argument to define the rate limit.
 
-
 
-
<font size = "1">Router(config-cs7-gtt-app-grp)#   pc 1.1.1 ssn 11  1  pcssn limit 2000</font>
 
-
 
-
The backup DPC does not define a rate limit.
 
-
 
-
<font size = "1">Router(config-cs7-gtt-app-grp)# pc 1.1.2 ssn 11  2  pcssn</font>
 
-
 
-
(Optional) Adds or changes a point code and optional subsystem number in the application group.
 
-
 
-
You must configure both a primary and backup DPC to take advantage of the GTT loadshare overflow feature.
 
-
 
-
You must assign a cost to the DPC to take advantage of the GTT overflow load sharing feature. The primary destination is defined by the lower cost. The rate limit is configured only on the primary destination.
 
-
 
-
* ''cost''—''' '''Index value (1-64). Specifies the priority of the DPC within the application group.
 
-
Use the '''limit '''keyword to specify the traffic limitations for a specific AS in a GTT application group. The '''limit''' keyword is configured only on the primary destination.
 
-
 
-
* '''limit'''—specifies the traffic limitation.
 
-
* ''rate''—defines the rate as an integer value from 1 to 4294967296 MSU/sec.
 
-
*
 
-
<font size = "1">'''exit'''</font>
 
-
 
-
*
 
-
<font size = "1">Router(config-cs7-gtt-app-grp)# exit</font>
 
-
 
-
Exits CS7 GTT application-group submode. '''Example'''
 
-
 
-
In the following example, the application group SMS-peak-on-weekdays has a primary DPC with a point code of 1.1.1 is limited to a rate of 2000 MSU per second. Any overflow traffic is sent to the backup DPC with a point code of 1.1.2. The primary DPC is defined by the lower cost of 1. The backup is defined by the higher cost of 2.
 
-
 
-
<font size = "1">cs7 gtt application-group SMS-peak-on-weekdays</font>
 
-
 
-
<font size = "1">multiplicity cost</font>
 
-
 
-
<font size = "1"> pc 1.1.1 ssn 11  1  pcssn limit 2000</font>
 
-
 
-
<font size = "1"> pc 1.1.2 ssn 11  2  pcssn</font>
 
-
 
-
In the following example, the application group SMS-peak-on-weekdays has a primary AS named weekday is limited to a rate of 2000 MSU per second. Any overflow traffic is sent to the backup AS named weekend. The primary AS is defined by the lower cost of 1. The AS is defined by the higher cost of 2.
 
-
 
-
<font size = "1">cs7 gtt application-group SMS-peak-on-weekdays</font>
 
-
 
-
<font size = "1">multiplicity cost</font>
 
-
 
-
<font size = "1"> asname weekday  1  gt  limit 2000</font>
 
-
 
-
<font size = "1"> asname weekend  2  gt</font>
 
-
 
-
'''Verifying and Monitoring'''
 
-
 
-
To verify the GTT SCCP overflow loadshare feature, use the following command in EXEC mode:
 
-
 
-
'''Command'''
 
-
 
-
'''Purpose'''
 
-
<font size = "1">Router# '''show cs7 '''''{'''''instance '''''instance''}'' id''''' rate-limit {pc '''''pc''''' | asname '''''as-name'''''}'''</font>
 
-
 
-
Displays the rate limit status of MTP overflow loadshare through the GTT application group .
 
-
<font size = "1">Router# '''show cs7 '''instance id''' gtt application-group name '''''application-group-name''''' rate-limit'''</font>
 
-
 
-
Displays the rate limit status of each line card for GTT SCCP loadshare overflow.
 
-
[[Category: Wireless/Mobility Configuration Examples]]
 
-
 
-
 
-
 
-
 
-
 
-
 
-
 
-
 
-
 
-
 
-
 
-
 
-
 
-
 
==Introduction==
==Introduction==
-
This configuration allows the ITP to send a user defined amount of traffic to a primary destination. Excess traffic is then sent to a secondary destination. This distribution is more specific than those based on congestion. Overflow load sharing is especially useful for enforcing customer limitations.
+
This configuration allows the Cisco IP Transfer Point (ITP) to send a user defined amount of traffic to a primary destination. Excess traffic is then sent to a secondary destination. This distribution is more specific than those based on congestion. Overflow load sharing is especially useful for enforcing customer limitations.
-
 
+
-
 
+
==Configuration==
==Configuration==
Line 172: Line 13:
* You can define the primary and secondary by configuring ASs, DPCs, or any combination of an AS and DPC.
* You can define the primary and secondary by configuring ASs, DPCs, or any combination of an AS and DPC.
* The primary AS or DPC is defined as the one with the lowest configured cost.
* The primary AS or DPC is defined as the one with the lowest configured cost.
-
'''CONFIGURATION STEPS'''
 
-
'''Command or Action'''
+
'''Example'''
-
'''Purpose'''
+
In the following example, the application group named SMS-peak-on-weekdays has a primary DPC with a point code of 1.1.1. It is limited to a rate of 2000 MSU per second. Any overflow traffic is sent to the backup DPC with a point code of 1.1.2. The primary DPC is defined by the lower cost of 1. The backup is defined by the higher cost of 2.
-
*
+
-
<font size = "1">'''enable'''</font>
+
-
 
+
-
*
+
-
<font size = "1">Router> enable</font>
+
-
 
+
-
Enables privileged EXEC mode.
+
-
 
+
-
* Enter your password if prompted.
+
-
*
+
-
<font size = "1">'''configure terminal'''</font>
+
-
 
+
-
*
+
-
<font size = "1">Router# configure terminal</font>
+
-
 
+
-
Enters global configuration mode.
+
-
*
+
-
<font size = "1">'''cs7 gtt application-group '''''group-name''</font>
+
-
 
+
-
*
+
-
<font size = "1">Router(config)# cs7 gtt application-group abc</font>
+
-
 
+
-
Defines the GTT application group and enables application-group submode.
+
-
*
+
-
<font size = "1">'''multiplicity '''</font>{<font size = "1">'''cost '''</font>|<font size = "1">''' share | cgpa | wrr'''</font>}
+
-
 
+
-
*
+
-
<font size = "1">Router(config-cs7-gtt-app-grp)#  multiplicity cost</font>
+
-
 
+
-
Specifies a method for selecting a destination for the application group.
+
-
 
+
-
* '''cost'''—Uses the destination with the least cost if that destination is available.
+
-
* '''share'''—Shares equally among all destinations.
+
-
* '''cgpa'''—Uses the SCCP calling party address (CGPA) field, which results in a weighted factor selection number for choosing the next destination from the available items in the application group.
+
-
* '''wrr'''—Applies weighted round robin load balancing (WRR) to SCCP class 0 and SCCP class 1 traffic.
+
-
* The '''cost '''keyword is used for overflow load sharing configurations.
+
-
*
+
-
<font size = "1">[</font><font size = "1">'''instance''' ''instance-number''] '''asname''' ''as-name'' {''cost'' ['''ssn''' ''ssn''] {'''gt''' ['''ntt''' ''ntt''] | '''pcssn'''} ['''limit''' ''rate''] | ''wf'' ['''ssn''' ''ssn''] {'''gt''' ['''ntt''' ''ntt''] | '''pcssn'''}}</font>
+
-
 
+
-
*
+
-
 
+
-
The primary AS use the '''limit '''keyword and ''rate ''argument to define the rate limit.
+
-
 
+
-
<font size = "1">Router(config-cs7-gtt-app-grp)#  asname weekday 1 gt limit 2000</font>
+
-
 
+
-
The backup AS does not define a rate limit.
+
-
 
+
-
<font size = "1">Router(config-cs7-gtt-app-grp)# asname weekday overflow 2  gt </font>
+
-
 
+
-
(Optional) Assigns an M3UA or SUA AS directly to a global title.
+
-
 
+
-
You must configure both a primary and backup AS to take advantage of the GTT loadshare overflow feature.
+
-
 
+
-
You must assign a cost to the AS to take advantage of the GTT overflow loadsharing feature. The primary destination is defined by the lower cost.
+
-
 
+
-
* ''cost''—''' '''Index value (1-64). Specifies the priority of the AS within the application group.
+
-
Use the '''limit '''keyword to limit traffic rate to a specific AS in a GTT application group. The rate limit is configured only on the primary destination.
+
-
 
+
-
* '''limit'''—Specifies the traffic-rate limitation.
+
-
* ''rate''—defines the rate as an integer value from 1 to 4294967296 MSU/sec.
+
-
*
+
-
<font size = "1">[</font><font size = "1">'''instance''' ''instance-number''] '''pc''''' pc'' ['''ssn''' ''ssn''] {''cost'' {'''gt'''['''ntt''' ''ntt'']|'''pcssn'''} ['''limit''' ''rate''] | ''wf ''{'''gt''' ['''ntt''' ''ntt'']|'''pcssn'''}}</font>
+
-
 
+
-
*
+
-
 
+
-
The primary DPC use the '''limit '''keyword and ''rate ''argument to define the rate limit.
+
-
 
+
-
<font size = "1">Router(config-cs7-gtt-app-grp)#   pc 1.1.1 ssn 11  1  pcssn limit 2000</font>
+
-
 
+
-
The backup DPC does not define a rate limit.
+
-
 
+
-
<font size = "1">Router(config-cs7-gtt-app-grp)# pc 1.1.2 ssn 11  2  pcssn</font>
+
-
 
+
-
(Optional) Adds or changes a point code and optional subsystem number in the application group.
+
-
 
+
-
You must configure both a primary and backup DPC to take advantage of the GTT loadshare overflow feature.
+
-
 
+
-
You must assign a cost to the DPC to take advantage of the GTT overflow load sharing feature. The primary destination is defined by the lower cost. The rate limit is configured only on the primary destination.
+
-
 
+
-
* ''cost''—''' '''Index value (1-64). Specifies the priority of the DPC within the application group.
+
-
Use the '''limit '''keyword to specify the traffic limitations for a specific AS in a GTT application group. The '''limit''' keyword is configured only on the primary destination.
+
-
 
+
-
* '''limit'''—specifies the traffic limitation.
+
-
* ''rate''—defines the rate as an integer value from 1 to 4294967296 MSU/sec.
+
-
*
+
-
<font size = "1">'''exit'''</font>
+
-
 
+
-
*
+
-
<font size = "1">Router(config-cs7-gtt-app-grp)# exit</font>
+
-
 
+
-
Exits CS7 GTT application-group submode. '''Example'''
+
-
 
+
-
In the following example, the application group SMS-peak-on-weekdays has a primary DPC with a point code of 1.1.1 is limited to a rate of 2000 MSU per second. Any overflow traffic is sent to the backup DPC with a point code of 1.1.2. The primary DPC is defined by the lower cost of 1. The backup is defined by the higher cost of 2.
+
<font size = "1">cs7 gtt application-group SMS-peak-on-weekdays</font>
<font size = "1">cs7 gtt application-group SMS-peak-on-weekdays</font>
Line 277: Line 24:
<font size = "1"> pc 1.1.1 ssn 11  1  pcssn limit 2000</font>
<font size = "1"> pc 1.1.1 ssn 11  1  pcssn limit 2000</font>
-
<font size = "1"> pc 1.1.2 ssn 11  2  pcssn</font>
+
<font size = "1"> pc 1.1.2 ssn 11  2  pcssn</font>'''
-
In the following example, the application group SMS-peak-on-weekdays has a primary AS named weekday is limited to a rate of 2000 MSU per second. Any overflow traffic is sent to the backup AS named weekend. The primary AS is defined by the lower cost of 1. The AS is defined by the higher cost of 2.
+
In the following example, the application group is named SMS-peak-on-weekdays. It has a primary AS named weekday and is limited to a rate of 2000 MSU per second. Any overflow traffic is sent to the backup AS named weekend. The primary AS is defined by the lower cost of 1. The AS is defined by the higher cost of 2.
<font size = "1">cs7 gtt application-group SMS-peak-on-weekdays</font>
<font size = "1">cs7 gtt application-group SMS-peak-on-weekdays</font>
Line 289: Line 36:
<font size = "1"> asname weekend  2  gt</font>
<font size = "1"> asname weekend  2  gt</font>
-
'''Verifying and Monitoring'''
+
==Related show Commands==
 +
This section provides information you can use to confirm your configuration is working properly.
-
To verify the GTT SCCP overflow loadshare feature, use the following command in EXEC mode:
+
<font size = "1">Router# '''show cs7 '''''{'''''instance '''''instance''}'' id''''' rate-limit {pc '''''pc''''' | asname '''''as-name'''''}'''</font>
-
'''Command'''
+
Displays the rate limit status of MTP overflow loadshare through the GTT application group.
-
'''Purpose'''
+
<font size = "1">Router# '''show cs7 '''instance id''' gtt application-group name '''''application-group-name''''' rate-limit'''</font>
-
<font size = "1">Router# '''show cs7 '''''{'''''instance '''''instance''}'' id''''' rate-limit {pc '''''pc''''' | asname '''''as-name'''''}'''</font>
+
-
 
+
-
Displays the rate limit status of MTP overflow loadshare through the GTT application group .
+
-
<font size = "1">Router# '''show cs7 '''instance id''' gtt application-group name '''''application-group-name''''' rate-limit'''</font>
+
Displays the rate limit status of each line card for GTT SCCP loadshare overflow.  
Displays the rate limit status of each line card for GTT SCCP loadshare overflow.  
[[Category: Wireless/Mobility Configuration Examples]]
[[Category: Wireless/Mobility Configuration Examples]]
-
==Related show Commands==
 
-
This section provides information you can use to confirm your configuration is working properly.
 
-
Certain show commands are supported by the [https://www.cisco.com/cgi-bin/Support/OutputInterpreter/home.pl Output Interpreter Tool (registered customers only)], which allows you to view an analysis of show command output.
+
''Certain show commands are supported by the [https://www.cisco.com/cgi-bin/Support/OutputInterpreter/home.pl Output Interpreter Tool (registered customers only)], which allows you to view an analysis of show command output.''
<!--Add steps to verify that the config is working, including which show commands to use-->
<!--Add steps to verify that the config is working, including which show commands to use-->
-
 
-
 
-
==Show running-config==
 
-
 
-
<pre>Add show running config of your device</pre>
 
==Related Information==
==Related Information==
-
[http://www.cisco.com/web/psa/products/index.html Technical Support & Documentation - Cisco Systems]
+
[http://www.cisco.com/en/US/products/sw/wirelssw/ps1862/products_feature_guides_list.html Cisco IP Transfer Point Feature Guides - Cisco Systems]
-
 
+
-
<!--List links to related information-->
+
-
 
+
-
<!--Add appropriate categories-->
+

Latest revision as of 13:56, 17 June 2010


Contents

Introduction

This configuration allows the Cisco IP Transfer Point (ITP) to send a user defined amount of traffic to a primary destination. Excess traffic is then sent to a secondary destination. This distribution is more specific than those based on congestion. Overflow load sharing is especially useful for enforcing customer limitations.

Configuration

Restrictions and Considerations

  • Only one rate limit entry is allowed for a GTT application group.
  • You configure the rate limit entry for a specific destination in the GTT application group.
  • You must configure both a primary and secondary (backup).
  • You can define the primary and secondary by configuring ASs, DPCs, or any combination of an AS and DPC.
  • The primary AS or DPC is defined as the one with the lowest configured cost.

Example

In the following example, the application group named SMS-peak-on-weekdays has a primary DPC with a point code of 1.1.1. It is limited to a rate of 2000 MSU per second. Any overflow traffic is sent to the backup DPC with a point code of 1.1.2. The primary DPC is defined by the lower cost of 1. The backup is defined by the higher cost of 2.

cs7 gtt application-group SMS-peak-on-weekdays

multiplicity cost

pc 1.1.1 ssn 11 1 pcssn limit 2000

pc 1.1.2 ssn 11 2 pcssn

In the following example, the application group is named SMS-peak-on-weekdays. It has a primary AS named weekday and is limited to a rate of 2000 MSU per second. Any overflow traffic is sent to the backup AS named weekend. The primary AS is defined by the lower cost of 1. The AS is defined by the higher cost of 2.

cs7 gtt application-group SMS-peak-on-weekdays

multiplicity cost

asname weekday 1 gt limit 2000

asname weekend 2 gt

Related show Commands

This section provides information you can use to confirm your configuration is working properly.

Router# show cs7 {instance instance} id rate-limit {pc pc | asname as-name}

Displays the rate limit status of MTP overflow loadshare through the GTT application group.

Router# show cs7 instance id gtt application-group name application-group-name rate-limit

Displays the rate limit status of each line card for GTT SCCP loadshare overflow.


Certain show commands are supported by the Output Interpreter Tool (registered customers only), which allows you to view an analysis of show command output.


Related Information

Cisco IP Transfer Point Feature Guides - Cisco Systems

Rating: 0.0/5 (0 votes cast)

Personal tools