Cisco Application Control Engine (ACE) Troubleshooting Guide -- Troubleshooting Ethernet Ports
Troubleshooting Ethernet Ports
There are four gigabit Ethernet (GE) ports in an ACE appliance with a full duplex throughput of 1 Gbps each. To check the status of a GE port, enter the following command:
switch/Admin# show interface gigabitEthernet 1/2’’’
GigabitEthernet Port 1/2 is UP, line protocol is UP <<<<<<<<<<<<<<<< If this shows down then check that the corresponding interface on Cat6k is not shutdown and also that the physical interface on ace-appliance is not shutdown. Verify that the physical connectivity with 3750 or cat6k is fine.
Hardware is ACE Appliance 1000Mb 802.3, address is 00:1b:24:93:21:cf MTU 9216 bytes Full-duplex, 1000Mb/s COS bits based QoS is disabled input flow-control is off, output flow-control is off 26556020169 packets input, 4515905164244 bytes, 0 dropped Received 15932917284 broadcasts (99696635 multicasts) 0 runts , 0 giants 0 FCS/Align errors , 0 runt FCS, 0 giant FCS 1 packets output, 64 bytes 1 broadcast, 0 multicast, 0 control output packets 0 underflow, 0 single collision, 0 multiple collision output packets 0 excessive collision and dropped, 0 Excessive Deferral and dropped
You can assign VLANs directly under the physical interface or using a channel group. These can be trunked or access ports. For trunked ports, the default native VLAN is 1, which can be changed using the ‘’’switchport trunk native vlan number’’’ command under the physical port or a channel group.
Configuring a Port Channel
interface port-channel 250
switchport trunk native vlan 3 switchport trunk allowed vlan 9,101-110,128,132,144,331,349 no shutdown
or interface port-channel 2
switchport access vlan 5 no shutdown
port-channel can be assigned to physical port using the channel-group command: interface gigabitEthernet 1/2
channel-group 250 shutdown
By default, the load-balancing scheme is source-dest-mac. You can change it to destination-ip, destination mac, and so on using the ‘’’port-channel load-balance <>’’’ command.
If the configured VLAN or BVI does not come up, verify that the assigned port-channel is up and that it is configured correctly on 3750/Catalyst 6500 series switch as well as the physical ports.
To check the status of the port channel, enter the following command:
switch/Admin# ‘’’show interface port-channel 250’’’
Description: mode: Trunk native vlan: 0 status: (UP), load-balance scheme: src-dst-mac <<< if the channel-group is up.
PortChannel 250 mapped phyport: 1/2 1/3 <<< the physical interfaces to which the channel-group is assigned. PortChannel 250 mapped active phyport: 1/3 <<< from the above list, list of active interface. PortChannel 250 allow vlan: vlan<9> vlan<101>-<110> vlan<128> vlan<132> vlan<144> vlan<331> vlan<349> << Assigned vlans
33581781 packets input, 2333352580 bytes, 0 dropped Received 20430421 broadcasts (13005450 multicasts) 0 runts , 0 giants 0 FCS/Align errors , 0 runt FCS, 0 giant FCS 10944303 packets output, 744212928 bytes 10944285 broadcast, 18 multicast, 0 control output packets 0 underflow, 0 single collision, 0 multiple collision output packets 0 excessive collision and dropped, 0 Excessive Deferral and dropped
Vlan assignment on physical ports:
interface gigabitEthernet 1/1
switchport access vlan 77 no shutdown
or interface gigabitEthernet 1/1
switchport trunk native vlan 3 switchport trunk allowed vlan 77 no shutdown
To check the list of VLANs that are up on the physical interface, enter the ‘’’show vlans’’’ command.
switch/Admin# show vlans Vlans configured on physical port(s)
vlan3 vlan5 vlan9-10 vlan30 vlan77 vlan101-110 vlan128 vlan132 vlan144 vlan331 vlan349
Finally, enter the show interface vlan command to see that the specified VLAN is up:
switch/Admin# show in interface inventory switch/Admin# show interface vlan 77
vlan77 is up, administratively up
Hardware type is VLAN MAC address is 00:1b:24:78:b1:e8 Virtual MAC address is 00:0b:fc:fe:1b:15 Mode : routed IP address is 184.108.40.206 netmask is 255.0.0.0 FT status is active Description:not set MTU: 1500 bytes Last cleared: never Last Changed: Thu Mar 18 13:27:20 2010 No of transitions: 1 Alias IP address not set Peer IP address is 220.127.116.11 Peer IP netmask is 255.0.0.0 Assigned on the physical port, up on the physical port
170 unicast packets input, 412878159 bytes 2231611 multicast, 3730365 broadcast 0 input errors, 0 unknown, 0 ignored, 0 unicast RPF drops 105 unicast packets output, 2949996 bytes 2 multicast, 45981 broadcast 0 output errors, 0 ignored