ASA Configuration Troubleshooting
IOS Version for ASA Device
The minimum supported IOS version of the ASA device is 8.x and later.
ASA Related Logs on CE Server
The ASA server related log on CE server can be found @ /var/log/CNSCE/asa/asa.log.
The minimum supported IOS version for the ASA device is 8.2 onwards.
Configuring the ASA device
Following CLIs should be configured on ASA device to communicate with CE server and work using call home protocol.
auto-update device-id [hostname] | [hardware-serial] | [ipaddress] | [mac-address]| string <device-name>
auto-update poll-period <period_in_minutes>
auto-update server https://<username>:<password>@<ce-server>:<port>/cns/ASAConfig
- device-name : Name of the ASA device.
- period_in_minutes : Poll period in minutes. On elapse of poll period, the ASA device will contact the CE server to pull its configuration and Image related information.
- username : CE Server's admin username.
- password : Password configured to the ASA device while creating the device on CE server.
- port : HTTPS server port. By default the port specifies to 443. If this port changed during setup, then the same should be used here.
Invalid remote host.
Make sure to add appropriate name <ce-server-ip-address> <ce-server-hostname> cli. As a work around you may use the IP address of CE server in auto-update server CLI instead of hostname.
How to enable auto-update server logging on ASA device.
Execute the following commands.
ASA-Device(config)# logging enable
ASA-Device(config)# logging console 6
ASA-Device# debug auto-update server
ASA-Device# debug auto-update client
Configuration not pulled due to java.lang.SecurityException: Device Authentication Failed.
Check the following.
1. Check whether the ASA device is created on CE server.
2. if the device is created on CE side, then check the auto-update server cli on ASA to verify that the CLI is having correct username and password.
3. If you feel that the password is incorrect on either side, then re-sync the password on both the side by reconfiguring the auto-update server CLI on ASA device and by editing the device on CE side.
Configuration not pulled.
This is because the device already downloaded associated template from CE server and the ASA device is running with updated configuration. Do the following to verify this.
1. Enable console/terminal logging on ASA device.
2. On elapse of poll-period ASA device will try to contact the CE server to retrieve the new template. During this time following log (not identical but similar) can be seen on ASA device console.
%ASA-6-302013: Built outbound TCP connection 23 for inside:cede1/443 (cede1/443) to identity:10.104.58.246/33894 (10.104.58.246/33894)
%ASA-6-725001: Starting SSL handshake with server inside:10.104.58.246/33894 for TLSv1 session.
%ASA-6-725002: Device completed SSL handshake with server inside:10.104.58.246/33894
Auto-update client: Sent DeviceDetails to /cns/ASAConfig of server cede1
Auto-update client: Processing UpdateInfo from server cede1
Component: config, [URL: https://cnsce-asauser:naveen@cede1:443/cns/ASAConfigProvider?deviceID=ASA-5520-246], checksum:xd2423c0873e3338bec5042a3e143b5e8
%ASA-6-725007: SSL session with server inside:10.104.58.246/33894 terminated.
%ASA-6-302014: Teardown TCP connection 23 for inside:cede1/443 to identity:10.104.58.246/33894 duration 0:00:00 bytes 1336 TCP Reset-I
Auto-update client: no need to update cfg
3. If the logging says that no need to update cfg, then the configuration associated to the ASA device on CE server and running configuration on ASA device are same and current.
Prerequisite for ASA/ASDM image upgrade.
Along with auto-update server configuration, following CLI should be exist on ASA device to ASA/ASDM image upgrade to happen.
boot system disk0:/<a-valid-asa-image-name>
asdm image disk0:/<a-valid-asdm-image-name>
Without these 2 CLIs the neither ASA image or ASDM image upgrade will happen.
ASA/ASDM image upgrade fails with error "could not open flash"
This failure could cause because of having not enough space on the flash card on the ASA device. Make sure that the flash have enough space on device before performing the image upgrade operation.
ASA/ASDM image upgrade know issues
Following are the known issues at this point which might impact the ASA/ASDM image upgrade on ASA devices.